Share via


Event ID 41023 — RRAS IGMP Socket Operation

Applies To: Windows Server 2008

Internet Group Management Protocol (IGMP) maintains host group membership on a local subnet. Hosts use IGMP to communicate multicast group membership requests with their local multicast router. Routers receive the group membership requests and periodically send queries to determine which host groups are active or inactive on the local subnet.

Socket operation for IGMP involves the configuration of the router to receive packets from the neighboring router.

 

Event Details

Product: Windows Operating System
ID: 41023
Source: Microsoft-Windows-RasRoutingProtocols-IGMPv2
Version: 6.0
Symbolic Name: IGMPLOG_EVENTSELECT_FAILED
Message: IGMPv2 was unable to request notification of events on the socket for the local interface with IP address: %1. The data is the error code. User Action: Check for low memory; invalid arguments; unsupported socket type; unsupported address family by the considered protocol family; already in use address; socket is already connected; no route to host; or insufficient memory available. For all cases except insufficient memory, check for socket connection configuration. In the case of insufficient memory, restart the system.

Resolve

Configure IGMP, check memory status, or restart Routing and Remote Access service

Possible resolutions:

  • Reconfigure IGMP on the local interface to request multicasting and to join the multicast group 224.0.0.9. For more information, see the "Configure IGMP" section.
  • This computer might be low on memory. For more information, see the "Check memory usage on the server" section.
  • Stop and restart the Routing and Remote Access service. For more information, see the "Restart the remote access service" section.
  • Restart the computer.

To perform these procedures, you must have membership in Administrators, or you must have been delegated the appropriate authority.

Configure IGMP

To configure IGMP:

  1. Open Routing and Remote Access. Click Start, click Run, type rrasmgmt.msc, and then press ENTER.
  2. In the console tree, expand IPv4, and then click IGMP.
  3. In the details pane, right-click the interface you want to configure, and then click Properties.
  4. Check the settings on the General and Router tabs.

Check memory usage on the server

To check memory usage on the remote access server:

  1. On the remote access server, click Start, click Run, type taskmgr, and then click OK.
  2. In the Windows Task Manager dialog box, click the Performance tab.
  3. Under Physical Memory, check the remote access server's memory usage.
  4. If necessary, free up available memory by ending non-essential applications or processes.

Restart the remote access service

To restart the remote access service:

  1. Open Routing and Remote Access. Click Start, click Run, type rrasmgmt.msc, and then press ENTER.
  2. By default, the local computer is listed as a server. To add another server, in the console tree, right-click Server Status, and then click Add Server. In the Add Server dialog box, click the appropriate option, and then click OK.
  3. In the console tree, right-click the server you want to restart, click All Tasks, and then click Restart.

Verify

You can verify multicast routing configuration with the mrinfo command. You can use the configuration information to aid in the troubleshooting of multicast forwarding and routing problems.

The mrinfo command queries a specified multicast router with an IGMP message. The response to the query contains a version number, the list of interfaces and the neighbors on each interface, metrics, Time to Live (TTL) thresholds, and flags. The syntax of the mrinfo command is:

mrinfo [-n] [ -i address ] [ -r retry_count ] [ -t timeout_count ] multicast_router

  • The -n option displays IP addresses in numeric format.
  • The -i option specifies the IP address of the interface from which you want to send the mrinfo query. By default, the interface from which to send the mrinfo query is determined by the IP routing table.
  • The -r option specifies the neighbor query retry limit. The default value is 3.
  • The -t option specifies how long, in seconds, mrinfo waits for a neighbor query reply. The default value is 4.

The following is an example of the mrinfo command:

C:\>mrinfo 10.1.0.1

10.1.0.1(test1.microsoft.com) [version 18.55,mtrace,snmp]:

10.1.0.1 -> 0.0.0.0 (local) [1/0/querier/leaf]

10.2.0.1 -> 10.2.0.2 (test2.microsoft.com) [1/0]

10.2.0.1 -> 10.2.0.3 (test3.microsoft.com) [1/0]

10.3.0.1 -> 0.0.0.0 (local) [1/0/querier/leaf]

In the preceding example, mrinfo is run against the multicast router at 10.1.0.1. The first line shows the multicast router configuration: version number (for servers running Routing and Remote Access, the version number reflects the build number of the operating system) and flags (mtrace and snmp supported).

Each additional line displays the interfaces on the multicast router and the neighbors on each interface. Interfaces 10.1.0.1 and 10.3.0.1 have no neighbors. Interface 10.2.0.1 has two neighbors, 10.2.0.2 and 10.2.0.3. For each line, mrinfo displays the interface and neighbor, the domain name for the neighbor, the multicast routing metric, the TTL threshold, and flags indicating its role on the network, such as the IGMP querier of the network (querier) or whether it has no neighbors (leaf).

RRAS IGMP Socket Operation

Routing and Remote Access Service Infrastructure