New-PublicFolderMoveRequest

The AcceptLargeDataLoss switch specifies that the request should continue even if a large number of items in the source mailbox can't be copied to the target mailbox. You don't need to specify a value with this switch.

You need to use this switch if you set the LargeItemLimit parameter to a value of 51 or higher. Otherwise, the command will fail.

The AllowLargeItems switch specifies that you can move large items only when they're encountered. You don't need to specify a value with this switch.

Large items are email messages with a maximum of 1,023 attachments.

The BadItemLimit parameter specifies the maximum number of bad items that are allowed before the request fails. A bad item is a corrupt item in the source mailbox that can't be copied to the target mailbox. Also included in the bad item limit are missing items. Missing items are items in the source mailbox that can't be found in the target mailbox when the request is ready to be completed.

Valid input for this parameter is an integer or the value unlimited. The default value is 0, which means that the request will fail if any bad items are detected. If you are OK with leaving a few bad items behind, you can set this parameter to a reasonable value (we recommend 10 or lower) so that the request can proceed. If too many bad items are detected, consider using the New-MailboxRepairRequest cmdlet to attempt to fix corrupted items in the source mailbox, and then try the request again.

The CompletedRequestAgeLimit parameter specifies how long the request will be kept after it has been completed before being automatically removed. The default value for this parameter is 30 days.

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

• Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
• Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.

This parameter is functional only in on-premises Exchange.

The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.

The Folders parameter specifies the public folders that you want to move. If the public folder has child public folders, these child public folders won't be moved unless you explicitly state them in the command. You can move multiple public folders by separating them with a comma, for example, \Dev\CustomerEngagements,\Dev\RequestsforChange,\Dev\Usability.

The InternalFlags parameter specifies the optional steps in the request. This parameter is used primarily for debugging purposes.

The Name parameter specifies the name of the public folder move request. If you don't specify a name, the default name is PublicFolderMove.

This parameter is available only in the cloud-based service.

{{ Fill Organization Description }}

The Priority parameter specifies the order in which the request should be processed in the request queue. Requests are processed in order, based on server health, status, priority, and last update time. Valid priority values are:

• Lowest
• Lower
• Low
• Normal: This is the default value.
• High
• Higher
• Highest
• Emergency

The RequestExpiryInterval parameter specifies an age limit for a completed or failed request. When you use this parameter, the completed or failed request is automatically removed after the specified interval expires. If you don't use this parameter:

• The completed request is automatically removed based on the CompletedRequestAgeLimit parameter value.
• If the request fails, you need to manually remove it by using the corresponding Remove-*Request cmdlet.

To specify a value, enter it as a time span: dd.hh:mm:ss where dd = days, hh = hours, mm = minutes, and ss = seconds.

When you use the value Unlimited, the completed request isn't automatically removed.

The Suspend switch specifies whether to suspend the request. You don't need to specify a value with this switch.

If you use this switch, the request is queued, but the request won't reach the status of InProgress until you resume the request with the relevant resume cmdlet.

The SuspendComment parameter specifies a description about why the request was suspended. You can only use this parameter if you specify the Suspend parameter.

This parameter is available only in on-premises Exchange.

The SuspendWhenReadyToComplete switch specifies whether to suspend the request before it reaches the status of CompletionInProgress. You don't need to specify a value with this switch.

After the move is suspended, it has a status of AutoSuspended. You can then manually complete the move by using the Resume-PublicFolderMoveRequest command.

The TargetMailbox parameter specifies the target public folder mailbox that you want to move the public folders to. You can use any value that uniquely identifies the mailbox. For example:

• Name
• Alias
• Distinguished name (DN)
• Canonical DN
• Domain\Username
• Email address
• GUID
• LegacyExchangeDN
• SamAccountName
• User ID or user principal name (UPN)

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.

The WorkloadType parameter is reserved for internal Microsoft use.