Export (0) Print
Expand All
This topic has not yet been rated - Rate this topic

Set-UMIPGateway

 

Applies to: Exchange Server 2013, Exchange Online

Topic Last Modified: 2012-09-13

Use the Set-UMIPGateway cmdlet to modify the configuration settings for a single Unified Messaging (UM) IP gateway or to return a list of configuration settings that can be modified on a specified UM IP gateway.

For information about the parameter sets in the Syntax section below, see Syntax.

Set-UMIPGateway -Identity <UMIPGatewayIdParameter> [-Address <UMSmartHost>] [-Confirm [<SwitchParameter>]] [-DelayedSourcePartyInfoEnabled <$true | $false>] [-DomainController <Fqdn>] [-ForceUpgrade <SwitchParameter>] [-IPAddressFamily <IPv4Only | IPv6Only | Any>] [-MessageWaitingIndicatorAllowed <$true | $false>] [-Name <String>] [-OutcallsAllowed <$true | $false>] [-Port <Int32>] [-Simulator <$true | $false>] [-Status <Enabled | Disabled | NoNewCalls>] [-WhatIf [<SwitchParameter>]]

This example modifies the IP address of the UM IP gateway MyUMIPGateway.

Set-UMIPGateway -Identity MyUMIPGateway -Address 10.10.10.1

This example prevents the UM IP gateway from accepting incoming calls and prevents outgoing calls.

Set-UMIPGateway -Identity MyUMIPGateway -Address 10.10.10.1 -Status Disabled -OutcallsAllowed $false

This example prevents the UM IP gateway MyUMIPGateway from accepting incoming calls and outgoing calls, sets an IPv6 address, and allows the UM IP gateway to use IPv4 and IPv6 addresses.

Set-UMIPGateway -Identity MyUMIPGateway -Address fe80::39bd:88f7:6969:d223%11 -IPAddressFamily Any -Status Disabled -OutcallsAllowed $false

This example enables the UM IP gateway to function as an IP gateway simulator and can be used with the Test-UMConnectivity cmdlet.

Set-UMIPGateway -Identity MyUMIPGateway -Simulator $true

The Set-UMIPGateway cmdlet modifies configuration settings for a specific UM IP gateway, for example, the IP address to the IP gateway. These modifications include allowing outgoing calls and controlling communications with a Session Initiation Protocol (SIP)–enabled IP Private Branch eXchange (PBX) or IP gateway.

ImportantImportant:
It's possible that modifications to the UM IP gateway settings may disrupt communication between Mailbox servers and the SIP-enabled IP PBX or IP gateway. Modifications to a UM IP gateway should be performed only by an administrator who fully understands the implications of making configuration changes to the UM IP gateway.

After this task is completed, the parameters and values specified are configured on the UM IP gateway.

You need to be assigned permissions before you can run this cmdlet. Although all parameters for this cmdlet are listed in this topic, you may not have access to some parameters if they're not included in the permissions assigned to you. To see what permissions you need, see the "UM IP gateways" entry in the Unified Messaging Permissions topic.

 

Parameter Required Type Description

Identity

Required

Microsoft.Exchange.Configuration.Tasks.UMIPGatewayIdParameter

The Identity parameter specifies the identifier for the UM IP gateway being modified. This parameter is the directory object ID for the UM IP gateway.

Address

Optional

Microsoft.Exchange.Data.UMSmartHost

The Address parameter specifies the IP address or the fully qualified domain name (FQDN) configured on the UM IP gateway or SIP-enabled IP PBX. An FQDN is required if the UM dial plan associated with the UM IP gateway is operating in SIP Secured or Secured mode. If an FQDN is used, verify that the Domain Name System (DNS) has been configured correctly.

Confirm

Optional

System.Management.Automation.SwitchParameter

The Confirm switch causes the command to pause processing and requires you to acknowledge what the command will do before processing continues. You don't have to specify a value with the Confirm switch.

DelayedSourcePartyInfoEnabled

Optional

System.Boolean

The DelayedSourcePartyInfoEnabled parameter specifies whether Unified Messaging should delay the process of accepting an inbound call from the Voice over IP (VoIP) gateway if the corresponding SIP INVITE of the call contains no calling party and diversion information.

DomainController

Optional

Microsoft.Exchange.Data.Fqdn

The DomainController parameter specifies the fully qualified domain name (FQDN) of the domain controller that writes this configuration change to Active Directory.

ForceUpgrade

Optional

System.Management.Automation.SwitchParameter

The ForceUpgrade switch specifies whether you're prompted for confirmation before a UM IP gateway object is upgraded.

IPAddressFamily

Optional

Microsoft.Exchange.Data.Directory.IPAddressFamily

The IPAddressFamily parameter specifies whether the UM IP gateway will use Internet Protocol version 4 (IPv4), IPv6, or both to communicate. If set to IPv4Only, the UM IP gateway will only use IPv4 to communicate. If set to IPv6Only, the UM IP gateway will only use IPv6. If set to Any, IPv6 will be used first, and then if necessary, it will fall back to IPv4. The default is IPv4Only.

MessageWaitingIndicatorAllowed

Optional

System.Boolean

The MessageWaitingIndicatorAllowed parameter specifies whether to enable the UM IP gateway to allow SIP NOTIFY messages to be sent to users associated with a UM dial plan and the UM IP gateway. The default value is $true.

Name

Optional

System.String

The Name parameter specifies the display name for the UM IP gateway. This display name is limited to 64 characters.

OutcallsAllowed

Optional

System.Boolean

The OutcallsAllowed parameter specifies whether to allow this UM IP gateway to be used for outgoing calls. This doesn't govern call transfers.

Port

Optional

System.Int32

The Port parameter specifies the IP port on which the IP gateway or IP PBX is listening. By default, it's port 5060. The range for this parameter is from 0 through 65535.

Simulator

Optional

System.Boolean

The Simulator parameter specifies the simulator used for the UM IP gateway being viewed. A simulator allows a client to connect to the Mailbox server.

Status

Optional

Microsoft.Exchange.Data.Directory.SystemConfiguration.GatewayStatus

The Status parameter specifies whether to enable or disable the UM IP gateway.

WhatIf

Optional

System.Management.Automation.SwitchParameter

The WhatIf switch instructs the command to simulate the actions that it would take on the object. By using the WhatIf switch, you can view what changes would occur without having to apply any of those changes. You don't have to specify a value with the WhatIf switch.

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn’t accept input data.

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn’t return data.

 
Did you find this helpful?
(1500 characters remaining)
Thank you for your feedback
Show:
© 2014 Microsoft. All rights reserved.