Export (0) Print
Expand All

New-UMIPGateway

 

Applies to: Exchange Server 2013, Exchange Online

Topic Last Modified: 2014-03-15

This cmdlet is available in on-premises Exchange Server 2013 and in the cloud-based service. Some parameters and settings may be exclusive to one environment or the other.

Use the New-UMIPGateway cmdlet to create a Unified Messaging (UM) IP gateway. A UM IP gateway is used to connect Unified Messaging servers to an IP gateway or a Session Initiation Protocol (SIP)–enabled IP Private Branch eXchange (PBX).

For information about the parameter sets in the Syntax section below, see Syntax.

New-UMIPGateway -Address <UMSmartHost> -Name <String> [-Confirm [<SwitchParameter>]] [-DomainController <Fqdn>] [-GlobalCallRoutingScheme <None | E164 | GatewayGuid | Reserved1 | Reserved2 | Reserved3>] [-IPAddressFamily <IPv4Only | IPv6Only | Any>] [-Organization <OrganizationIdParameter>] [-UMDialPlan <UMDialPlanIdParameter>] [-WhatIf [<SwitchParameter>]]

This example creates the UM IP gateway MyUMIPGateway that enables a Mailbox server to start accepting calls from an IP gateway with an IP address of 10.10.10.1.

New-UMIPGateway -Identity MyUMIPGateway -Address 10.10.10.1

This example creates the UM IP gateway MyUMIPGateway and prevents it from accepting incoming calls and outgoing calls, sets an IPv6 address, and allows the UM IP gateway to use IPv4 and IPV6 addresses.

New-UMIPGateway -Identity MyUMIPGateway -Address fe80::39bd:88f7:6969:d223%11 -IPAddressFamily Any -Status Disabled -OutcallsAllowed $false

This example creates the UM IP gateway MyUMIPGateway that enables a Mailbox server to start accepting calls from an IP gateway with an FQDN of MyUMIPGateway.contoso.com.

New-UMIPGateway -Identity MyUMIPGateway -Address "MyUMIPGateway.contoso.com"

The New-UMIPGateway cmdlet creates a UM IP gateway. A UM IP gateway has organization-wide scope and references a single physical IP gateway. The UM IP gateway that's created is used to establish a connection to an IP gateway or a SIP-enabled IP PBX. After this task is completed, a new UM IP gateway is created.

You need to be assigned permissions before you can run this cmdlet. Although all parameters for this cmdlet are listed in this topic, you may not have access to some parameters if they're not included in the permissions assigned to you. To see what permissions you need, see the "UM IP gateways" entry in the Unified Messaging permissions topic.

 

Parameter Required Type Description

Address

Required

Microsoft.Exchange.Data.UMSmartHost

The Address parameter specifies the IP address configured on the IP gateway or SIP-enabled IP PBX.

Name

Required

System.String

The Name parameter specifies the display name for the UM IP gateway. The name for the new UM IP gateway can contain up to 64 characters.

Confirm

Optional

System.Management.Automation.SwitchParameter

The Confirm switch causes the command to pause processing and requires you to acknowledge what the command will do before processing continues. You don't have to specify a value with the Confirm switch.

DomainController

Optional

Microsoft.Exchange.Data.Fqdn

This parameter is available only in on-premises Exchange 2013.

The DomainController parameter specifies the fully qualified domain name (FQDN) of the domain controller that writes this configuration change to Active Directory.

GlobalCallRoutingScheme

Optional

Microsoft.Exchange.Data.Directory.SystemConfiguration.UMGlobalCallRoutingScheme

The GlobalCallRoutingScheme parameter specifies whether the IP gateway can accept calls for UM-enabled users and auto attendant numbers included in the global routing database. If the value is set to E164, the IP gateway accepts the call.

IPAddressFamily

Optional

Microsoft.Exchange.Data.Directory.IPAddressFamily

The IPAddressFamily parameter specifies whether the UM IP gateway uses Internet Protocol version 4 (IPv4), IPv6, or both to communicate. If set to IPv4Only, the UM IP gateway only uses IPv4 to communicate. If set to IPv6Only, the UM IP gateway only uses IPv6. If set to Any, IPv6 will be used first, and then, if necessary, it will fallback to IPv4. The default is IPv4Only.

Organization

Optional

Microsoft.Exchange.Configuration.Tasks.OrganizationIdParameter

The Organization parameter is reserved for internal Microsoft use.

UMDialPlan

Optional

Microsoft.Exchange.Configuration.Tasks.UMDialPlanIdParameter

The UMDialPlan parameter specifies the UM dial plan to be associated with the UM IP gateway.

WhatIf

Optional

System.Management.Automation.SwitchParameter

The WhatIf switch instructs the command to simulate the actions that it would take on the object. By using the WhatIf switch, you can view what changes would occur without having to apply any of those changes. You don't have to specify a value with the WhatIf switch.

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn’t accept input data.

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn’t return data.

 
Was this page helpful?
(1500 characters remaining)
Thank you for your feedback
Show:
© 2014 Microsoft