Export (0) Print
Expand All
This topic has not yet been rated - Rate this topic

Set-RoutingGroupConnector

Applies to: Exchange Server 2010

Topic Last Modified: 2011-03-19

Use the Set-RoutingGroupConnector cmdlet to modify the properties of an existing routing group connector between a Microsoft Exchange Server 2010 routing group and an Exchange Server 2003 routing group. You can also use this cmdlet to configure the maximum message size that can pass across a routing group connector.


Set-RoutingGroupConnector -Identity <RoutingGroupConnectorIdParameter> [-Confirm [<SwitchParameter>]] [-Cost <Int32>] [-DomainController <Fqdn>] [-MaxMessageSize <Unlimited>] [-Name <String>] [-PublicFolderReferralsEnabled <$true | $false>] [-SourceTransportServers <MultiValuedProperty>] [-TargetTransportServers <MultiValuedProperty>] [-WhatIf [<SwitchParameter>]]

Parameter Required Type Description

Identity

Required

Microsoft.Exchange.Configuration.Tasks.RoutingGroupConnectorIdParameter

The Identity parameter specifies the name or GUID of the routing group connector. The name is expressed as [[Administrative Group Name\]Routing Group Name]\Routing Group Connector Name.

Confirm

Optional

System.Management.Automation.SwitchParameter

The Confirm switch causes the command to pause processing and requires you to acknowledge what the command will do before processing continues. You don't have to specify a value with the Confirm switch.

Cost

Optional

System.Int32

The Cost parameter specifies a cost to the connector. Transport servers use the connector cost to determine the least cost routing path from a source server to the destination server for message delivery.

DomainController

Optional

Microsoft.Exchange.Data.Fqdn

The DomainController parameter specifies the fully qualified domain name (FQDN) of the domain controller that writes this configuration change to Active Directory.

MaxMessageSize

Optional

Microsoft.Exchange.Data.Unlimited

The MaxMessageSize parameter specifies the maximum size of a message that can pass through a routing group connector. The default value is unlimited. When you enter a value, qualify the value with one of the following units:

  • B (bytes)
  • KB (kilobytes)
  • MB (megabytes)
  • GB (gigabytes)

Unqualified values are treated as bytes. The valid input range for this parameter is from 64KB through Int64. To remove the message size limit on a Send connector, enter a value of unlimited.

Name

Optional

System.String

The Name parameter specifies the name of the routing group connector.

PublicFolderReferralsEnabled

Optional

System.Boolean

The PublicFolderReferralsEnabled parameter specifies whether users can use this routing group connector to access a public folder replica located in the routing group of the target servers when an instance of that public folder isn't available in the same routing group as the user's mailbox. The default value is $true.

SourceTransportServers

Optional

Microsoft.Exchange.Data.MultiValuedProperty

The SourceTransportServers parameter specifies the host name or FQDN of the transport servers that are used to send messages to the target transport servers. You can specify more than one server by separating each entry with a comma. For more information about how to add or remove values from multivalued properties, see Modifying Multivalued Properties.

TargetTransportServers

Optional

Microsoft.Exchange.Data.MultiValuedProperty

The TargetTransportServers parameter specifies the host name or FQDN of the transport servers that receive messages from the source transport servers. You can specify more than one server by separating each entry with a comma. For more information about how to add or remove values from multivalued properties, see Modifying Multivalued Properties.

WhatIf

Optional

System.Management.Automation.SwitchParameter

The WhatIf switch instructs the command to simulate the actions that it would take on the object. By using the WhatIf switch, you can view what changes would occur without having to apply any of those changes. You don't have to specify a value with the WhatIf switch.

The Set-RoutingGroupConnector cmdlet modifies the properties of an existing routing group connector. A routing group connector is used to send and receive messages between computers running Exchange 2010 that have the Hub Transport server role installed and Exchange 2003 bridgehead servers when the organization is running more than one version of Exchange.

The Exchange 2003 source servers specified in this cmdlet are automatically added to the ExchangeLegacyInterop universal security group. By default, the Exchange 2010 system grants Send to and Receive from permissions on the Hub Transport servers to members of this group. The source and target servers must be computers that have the Exchange 2010 Hub Transport server role installed, or Exchange 2003 bridgehead servers.

You need to be assigned permissions before you can run this cmdlet. Although all parameters for this cmdlet are listed in this topic, you may not have access to some parameters if they're not included in the permissions assigned to you. To see what permissions you need, see the "Routing group connectors" entry in the Transport Permissions topic.

This example makes the following configuration changes to the routing group connector Ex2010 to Ex2003 RGC:

  • Sets the cost to 70.
  • Sets a maximum message size limit of 10 MB.
  • Specifies new source and target servers for the connector.
Set-RoutingGroupConnector -Identity "Exchange Administrative Group (FYDIBOHF23SPDLT)\Exchange Routing Group (DWBGZMFD01QNBJR)\Ex2010 to Ex2003 RGC" -Cost 70 -MaxMessageSize 10MB -SourceTransportServers 2010Hub1.contoso.com -TargetTransportServers 2003BH1.contoso.com
Did you find this helpful?
(1500 characters remaining)
Thank you for your feedback
Show:
© 2014 Microsoft. All rights reserved.