Export (0) Print
Expand All
Expand Minimize

Set-MailboxRestoreRequest

 

Applies to: Exchange Server 2013

This cmdlet is available only in on-premises Exchange Server 2013.

Use the Set-MailboxRestoreRequest cmdlet to change restore request options after the request has been created. You can use this cmdlet to recover from failed restore requests.

For information about the parameter sets in the Syntax section below, see Syntax.

Set-MailboxRestoreRequest [-AcceptLargeDataLoss <SwitchParameter>] [-BadItemLimit <Unlimited>] [-BatchName <String>] [-CompletedRequestAgeLimit <Unlimited>] [-InternalFlags <InternalMrsFlag[]>] [-LargeItemLimit <Unlimited>] [-Priority <Lowest | Lower | Low | Normal | High | Higher | Highest | Emergency>] [-SkipMerging <SkippableMergeComponent[]>] <COMMON PARAMETERS>

Set-MailboxRestoreRequest -RehomeRequest <SwitchParameter> <COMMON PARAMETERS>

COMMON PARAMETERS: -Identity <MailboxRestoreRequestIdParameter> [-Confirm [<SwitchParameter>]] [-DomainController <Fqdn>] [-RemoteCredential <PSCredential>] [-RemoteHostName <Fqdn>] [-WhatIf [<SwitchParameter>]]

This example changes the second restore request for Ayla\MailboxRestore1 to skip 10 corrupt mailbox items.

Set-MailboxRestoreRequest -Identity "Ayla\MailboxRestore1" -BadItemLimit 10

This example changes the first restore request for Kweku's mailbox to skip 100 corrupt items. Because the BadItemLimit is greater than 50, the AcceptLargeDataLoss parameter must be specified.

Set-MailboxRestoreRequest -Identity "Kweku\MailboxRestore" -BadItemLimit 100 -AcceptLargeDataLoss

You need to be assigned permissions before you can run this cmdlet. Although all parameters for this cmdlet are listed in this topic, you may not have access to some parameters if they're not included in the permissions assigned to you. To see what permissions you need, see the "Mailbox restore request" entry in the Recipients Permissions topic.

 

Parameter Required Type Description

Identity

Required

Microsoft.Exchange.MailboxReplicationService.MailboxRestoreRequestIdParameter

The Identity parameter specifies the identity of the restore request. The Identity parameter consists of the alias of the mailbox to be restored and the name that was specified when the restore request was created. The identity of the restore request uses the following syntax: <alias>\<name>

If you didn't specify a name for the restore request when it was created, Exchange automatically generated the default name MailboxRestore. Exchange generates up to 10 names, starting with MailboxRestore and then MailboxRestoreX (where X = 1–9).

RehomeRequest

Required

System.Management.Automation.SwitchParameter

The RehomeRequest switch specifies that the mailbox restore request be moved to a different mailbox database. Use this parameter to edit a mailbox restore request in the case where the source mailbox database from the original move request has to be removed.

AcceptLargeDataLoss

Optional

System.Management.Automation.SwitchParameter

The AcceptLargeDataLoss parameter specifies that a large amount of data loss is acceptable if the BadItemLimit is set to 51 or higher. Items are considered corrupted if the item can't be read from the source database or can't be written to the target database. Corrupted items won't be available in the destination mailbox or .pst file.

BadItemLimit

Optional

Microsoft.Exchange.Data.Unlimited

The BadItemLimit parameter specifies the number of bad items to skip if the request encounters corruption in the mailbox. Use 0 to not skip bad items. The valid input range for this parameter is from 0 through 2147483647. The default value is 0. We recommend that you keep the default value 0 and only change the BadItemLimit parameter value if the request fails.

NoteNote:
If you set the BadItemLimit parameter to more than 50, the command fails, and you receive a warning stating: "Please confirm your intention to accept a large amount of data loss by specifying AcceptLargeDataLoss." If you receive this warning, you need to run the command again, this time using the AcceptLargeDataLoss parameter. No further warnings appear, and any corrupted items aren't available after the process is complete.

BatchName

Optional

System.String

The BatchName parameter specifies the name of the batch. Use this parameter to change, create, or remove a batch name.

To remove a batch name, set the BatchName parameter value to an empty string or to null, for example, -BatchName "" or -BatchName $null.

CompletedRequestAgeLimit

Optional

Microsoft.Exchange.Data.Unlimited

The CompletedRequestAgeLimit parameter specifies how long the status of a completed restore request is set to Completed. If this parameter is set to a value of 0, the status is cleared immediately instead of changing it to Completed.

Confirm

Optional

System.Management.Automation.SwitchParameter

The Confirm switch causes the command to pause processing and requires you to acknowledge what the command will do before processing continues. You don't have to specify a value with the Confirm switch.

DomainController

Optional

Microsoft.Exchange.Data.Fqdn

The DomainController parameter specifies the fully qualified domain name (FQDN) of the domain controller that writes this configuration change to Active Directory.

InternalFlags

Optional

Microsoft.Exchange.Management.RecipientTasks.InternalMrsFlag[]

The InternalFlags parameter specifies the optional steps in the request. This parameter is used primarily for debugging purposes.

LargeItemLimit

Optional

Microsoft.Exchange.Data.Unlimited

The LargeItemLimit parameter specifies the number of items to skip in the mailbox because these items exceed the item size limit in the target mailbox data. Use 0 to not skip any large items.

NoteNote:
If you set the LargeItemLimit parameter to 51 or higher, you must also include the AcceptLargeDataLoss parameter.

Priority

Optional

Microsoft.Exchange.MailboxReplicationService.RequestPriority

The Priority parameter specifies the priority of the mailbox restore request. Use one of the following values:

  • Emergency

  • Highest

  • Higher

  • High

  • Normal

  • Low

  • Lower

  • Lowest

RemoteCredential

Optional

System.Management.Automation.PSCredential

This parameter is reserved for internal Microsoft use.

RemoteHostName

Optional

Microsoft.Exchange.Data.Fqdn

This parameter is reserved for internal Microsoft use.

SkipMerging

Optional

Microsoft.Exchange.Management.RecipientTasks.SkippableMergeComponent[]

The SkipMerging parameter specifies folder-related items to skip when restoring the mailbox. Use one of the following values:

  • FolderRules

  • FolderACLs

  • InitialConnectionValidation

Use this parameter only if a restore request fails because of folder rules, folder access control lists (ACLs), or initial connection validation.

WhatIf

Optional

System.Management.Automation.SwitchParameter

The WhatIf switch instructs the command to simulate the actions that it would take on the object. By using the WhatIf switch, you can view what changes would occur without having to apply any of those changes. You don't have to specify a value with the WhatIf switch.

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn’t accept input data.

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn’t return data.

 
Was this page helpful?
(1500 characters remaining)
Thank you for your feedback
Show:
© 2014 Microsoft