Export (0) Print
Expand All
Expand Minimize
This topic has not yet been rated - Rate this topic

New-HostedConnectionFilterPolicy

Exchange 2013
 

Applies to: Exchange Online Protection, Exchange Online

Topic Last Modified: 2012-12-14

This cmdlet is available only in the cloud-based service.

Use the Set-HostedConnectionFilterPolicy cmdlet to create connection filter policies in your cloud-based organization.

For information about the parameter sets in the Syntax section below, see Syntax.

New-HostedConnectionFilterPolicy -Name <String> [-AdminDisplayName <String>] [-Confirm [<SwitchParameter>]] [-DomainController <Fqdn>] [-EnableSafeList <$true | $false>] [-IgnoreDehydratedFlag <SwitchParameter>] [-IPAllowList <MultiValuedProperty>] [-IPBlockList <MultiValuedProperty>] [-Organization <OrganizationIdParameter>] [-WhatIf [<SwitchParameter>]]

This example creates a new connection filter policy named Contoso Connection Filter Policy with the following settings:

  • Messages from 192.168.1.10 are never identified as spam.

  • Messages from 10.10.10.10/24 are always identified as spam.

New-HostedConnectionFilterPolicy -Name "Contoso Connection Filter Policy" -IPAllowList 192.168.1.10 -IPBlockList 10.10.10.10/24

You need to be assigned permissions before you can run this cmdlet. Although all parameters for this cmdlet are listed in this topic, you may not have access to some parameters if they're not included in the permissions assigned to you. To see what permissions you need, see the "Anti-spam" entry in the Feature Permissions in Exchange Online topic.

 

Parameter Required Type Description

Name

Required

System.String

The Name parameter specifies a unique name for the connection filter policy.

AdminDisplayName

Optional

System.String

The AdminDisplayName parameter specifies a description for the connection filter policy. If the value contains spaces, enclose the value in quotation marks (").

Confirm

Optional

System.Management.Automation.SwitchParameter

The Confirm switch causes the command to pause processing and requires you to acknowledge what the command will do before processing continues. You don't have to specify a value with the Confirm switch.

DomainController

Optional

Microsoft.Exchange.Data.Fqdn

This parameter is reserved for internal Microsoft use.

EnableSafeList

Optional

System.Boolean

The EnableSafeList parameter enables or disables use of the safe list. The safe list is a dynamic allow list in the Microsoft datacenter that requires no customer configuration. Valid input for this parameter is $true or $false. The default value is $false.

IgnoreDehydratedFlag

Optional

System.Management.Automation.SwitchParameter

This parameter is reserved for internal Microsoft use.

IPAllowList

Optional

Microsoft.Exchange.Data.MultiValuedProperty

The IPAllowList parameter specifies IP addresses from which messages are always allowed. Messages from the IP addresses you specify won't be identified as spam, despite any other spam characteristics of the messages.

You enter the IP addresses using the following syntax:

  • Single IP: For example, 192.168.1.1.

  • IP range: You can use an IP address range, for example, 192.168.0.1-192.168.0.254.

  • CIDR IP: You can use Classless InterDomain Routing (CIDR), for example, 192.168.0.1/25.

You can specify multiple IP addresses or address ranges separated by commas.

IPBlockList

Optional

Microsoft.Exchange.Data.MultiValuedProperty

The IPBlockList parameter specifies IP addresses from which messages are never allowed. Messages from the IP addresses you specify are blocked without any further spam scanning.

You enter the IP addresses using the following syntax:

  • Single IP: For example, 192.168.1.1.

  • IP range: You can use an IP address range, for example, 192.168.0.1-192.168.0.254.

  • CIDR IP: You can use Classless InterDomain Routing (CIDR), for example, 192.168.0.1/25.

You can specify multiple IP addresses or address ranges separated by commas.

Organization

Optional

Microsoft.Exchange.Configuration.Tasks.OrganizationIdParameter

The Organization parameter is reserved for internal Microsoft use.

WhatIf

Optional

System.Management.Automation.SwitchParameter

The WhatIf switch instructs the command to simulate the actions that it would take on the object. By using the WhatIf switch, you can view what changes would occur without having to apply any of those changes. You don't have to specify a value with the WhatIf switch.

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn’t accept input data.

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn’t return data.

 
Did you find this helpful?
(1500 characters remaining)
Thank you for your feedback
Show:
© 2014 Microsoft. All rights reserved.