Microsoft Security Bulletin MS10-062 - Critical

Installing the Update

When you install this security update, the installer checks whether one or more of the files that are being updated on your system have previously been updated by a Microsoft hotfix.

If you have previously installed a hotfix to update one of these files, the installer copies the RTMQFE, SP1QFE, or SP2QFE files to your system. Otherwise, the installer copies the RTMGDR, SP1GDR, or SP2GDR files to your system. Security updates may not contain all variations of these files. For more information about this behavior, see Microsoft Knowledge Base Article 824994.

For more information about the installer, visit the Microsoft TechNet Web site.

For more information about the terminology that appears in this bulletin, such as hotfix, see Microsoft Knowledge Base Article 824684.

This security update supports the following setup switches.

Note You can combine these switches into one command. For backward compatibility, the security update also supports the setup switches that the earlier version of the Setup program uses. For more information about the supported installation switches, see Microsoft Knowledge Base Article 262841.

Removing the Update

This security update supports the following setup switches.

Verifying That the Update Has Been Applied

• Microsoft Baseline Security Analyzer

  To verify that a security update has been applied to an affected system, you may be able to use the Microsoft Baseline Security Analyzer (MBSA) tool. See the section, Detection and Deployment Tools and Guidance, earlier in this bulletin for more information.

• File Version Verification

  Because there are several editions of Microsoft Windows, the following steps may be different on your system. If they are, see your product documentation to complete these steps.

  1. Click Start, and then click Search.
  2. In the Search Results pane, click All files and folders under Search Companion.
  3. In the All or part of the file name box, type a file name from the appropriate file information table, and then click Search.
  4. In the list of files, right-click a file name from the appropriate file information table, and then click Properties.
     
     Note Depending on the edition of the operating system, or the programs that are installed on your system, some of the files that are listed in the file information table may not be installed.
  5. On the Version tab, determine the version of the file that is installed on your system by comparing it to the version that is documented in the appropriate file information table.
     
     Note Attributes other than the file version may change during installation. Comparing other file attributes to the information in the file information table is not a supported method of verifying that the update has been applied. Also, in certain cases, files may be renamed during installation. If the file or version information is not present, use one of the other available methods to verify update installation.
• Registry Key Verification

  You may also be able to verify the files that this security update has installed by reviewing the registry keys listed in the Reference Table in this section.

  These registry keys may not contain a complete list of installed files. Also, these registry keys may not be created correctly when an administrator or an OEM integrates or slipstreams this security update into the Windows installation source files.

Installing the Update

When you install this security update, the installer checks to see if one or more of the files that are being updated on your system have previously been updated by a Microsoft hotfix.

If you have previously installed a hotfix to update one of these files, the installer copies the RTMQFE, SP1QFE, or SP2QFE files to your system. Otherwise, the installer copies the RTMGDR, SP1GDR, or SP2GDR files to your system. Security updates may not contain all variations of these files. For more information about this behavior, see Microsoft Knowledge Base Article 824994.

For more information about the installer, visit the Microsoft TechNet Web site.

For more information about the terminology that appears in this bulletin, such as hotfix, see Microsoft Knowledge Base Article 824684.

This security update supports the following setup switches.

Note You can combine these switches into one command. For backward compatibility, the security update also supports many of the setup switches that the earlier version of the Setup program uses. For more information about the supported installation switches, see Microsoft Knowledge Base Article 262841.

Removing the Update

This security update supports the following setup switches.

Verifying that the Update Has Been Applied

• Microsoft Baseline Security Analyzer

  To verify that a security update has been applied to an affected system, you may be able to use the Microsoft Baseline Security Analyzer (MBSA) tool. See the section, Detection and Deployment Tools and Guidance, earlier in this bulletin for more information.

• File Version Verification

  Because there are several editions of Microsoft Windows, the following steps may be different on your system. If they are, see your product documentation to complete these steps.

  1. Click Start, and then click Search.
  2. In the Search Results pane, click All files and folders under Search Companion.
  3. In the All or part of the file name box, type a file name from the appropriate file information table, and then click Search.
  4. In the list of files, right-click a file name from the appropriate file information table, and then click Properties.
     
     Note Depending on the edition of the operating system, or the programs that are installed on your system, some of the files that are listed in the file information table may not be installed.
  5. On the Version tab, determine the version of the file that is installed on your system by comparing it to the version that is documented in the appropriate file information table.
     
     Note Attributes other than the file version may change during installation. Comparing other file attributes to the information in the file information table is not a supported method of verifying that the update has been applied. Also, in certain cases, files may be renamed during installation. If the file or version information is not present, use one of the other available methods to verify update installation.
• Registry Key Verification

  You may also be able to verify the files that this security update has installed by reviewing the registry keys listed in the Reference Table in this section.

  These registry keys may not contain a complete list of installed files. Also, these registry keys may not be created correctly when an administrator or an OEM integrates or slipstreams this security update into the Windows installation source files.

Installing the Update

When you install this security update, the installer checks whether one or more of the files that are being updated on your system have previously been updated by a Microsoft hotfix.

For more information about the terminology that appears in this bulletin, such as hotfix, see Microsoft Knowledge Base Article 824684.

This security update supports the following setup switches.

Note For more information about the wusa.exe installer, see Microsoft Knowledge Base Article 934307.

Verifying That the Update Has Been Applied

• Microsoft Baseline Security Analyzer

  To verify that a security update has been applied to an affected system, you may be able to use the Microsoft Baseline Security Analyzer (MBSA) tool. See the section, Detection and Deployment Tools and Guidance, earlier in this bulletin for more information.

• File Version Verification

  Because there are several editions of Microsoft Windows, the following steps may be different on your system. If they are, see your product documentation to complete these steps.

  1. Click Start and then enter an update file name in the Start Search box.
  2. When the file appears under Programs, right-click the file name and click Properties.
  3. On the General tab, compare the file size with the file information tables provided in the bulletin KB article.
  4. You can also click the Details tab and compare information, such as file version and date modified, with the file information tables provided in the bulletin KB article.
  5. Finally, you can also click the Previous Versions tab and compare file information for the previous version of the file with the file information for the new, or updated, version of the file.

Installing the Update

When you install this security update, the installer checks whether one or more of the files that are being updated on your system have previously been updated by a Microsoft hotfix.

For more information about the terminology that appears in this bulletin, such as hotfix, see Microsoft Knowledge Base Article 824684.

This security update supports the following setup switches.

Note For more information about the wusa.exe installer, see Microsoft Knowledge Base Article 934307.

Verifying That the Update Has Been Applied

• Microsoft Baseline Security Analyzer

  To verify that a security update has been applied to an affected system, you may be able to use the Microsoft Baseline Security Analyzer (MBSA) tool. See the section, Detection and Deployment Tools and Guidance, earlier in this bulletin for more information.

• File Version Verification

  Because there are several editions of Microsoft Windows, the following steps may be different on your system. If they are, see your product documentation to complete these steps.

  1. Click Start and then enter an update file name in the Start Search box.
  2. When the file appears under Programs, right-click the file name and click Properties.
  3. On the General tab, compare the file size with the file information tables provided in the bulletin KB article.
  4. You can also click the Details tab and compare information, such as file version and date modified, with the file information tables provided in the bulletin KB article.
  5. Finally, you can also click the Previous Versions tab and compare file information for the previous version of the file with the file information for the new, or updated, version of the file.