Share via


RRAS Audits

Applies To: Windows Server 2008 R2

The Routing and Remote Access service has determined that RRAS audits generated an audit entry when a system event was executed successfully. These events confirm successful Routing and Remote Access operations.

Events

Event ID Source Message

20015

RemoteAccess

The user: %1 has connected and has been successfully authenticated on port: %2.

20048

RemoteAccess

The user: %1 connected on port: %2 on: %3 at: %4 and disconnected on: %5 at: %6. The user was active for: %7 minutes, %8 seconds. %9 bytes were sent and %10 bytes were received. The port speed was: %11. The reason for disconnecting was: %12.

20064

RemoteAccess

The user: %1 on port: %2 was called back at the number: %3.

20088

RemoteAccess

The remote access server acquired IP address: %1

20139

RemoteAccess

The port: %1 has been disconnected due to inactivity.

20140

RemoteAccess

The port: %1 has been disconnected because the user reached the maximum connect time allowed by the administrator.

20141

RemoteAccess

The user: %1 has connected and has been successfully authenticated on port: %2. Data sent and received over this link is encrypted.

20142

RemoteAccess

The user: %1 has connected and has been successfully authenticated on port: %2. Data sent and received over this link is strongly encrypted.

20158

RemoteAccess

The user: %1 has successfully established a connection to: %2 using the device: %3.

20159

RemoteAccess

The connection to: %1 made by user: %2 using device: %3 was disconnected.

20161

RemoteAccess

The user: %1 successfully established a connection to: %2 using the device: %3. This connection happened automatically because the bandwidth utilization was high.

20162

RemoteAccess

The remote access server established a connection to: %1 for the user: %2 using the device: %3. This connection happened automatically because the bandwidth utilization was high.

20163

RemoteAccess

The connection to: %1 made by user: %2 using device: %3 was disconnected. This disconnection happened automatically because the bandwidth utilization was low.

20164

RemoteAccess

A link in the connection to: %1 made by user: %2 should be disconnected. The bandwidth utilization is too low.

20186

RemoteAccess

Interface: %1 is now reachable.

20190

RemoteAccess

Because no certificate has been configured for clients dialing in with EAP-TLS, a default certificate is being sent to user: %1. Go to the user's remote access policy and configure the Extensible Authentication Protocol (EAP).

20194

RemoteAccess

The user: %1 connected on port: %2 on: %3 at: %4 and disconnected on: %5 at: %6. The user was active for: %7 minutes %8 seconds. %9 bytes were sent and %10 bytes were received. The reason for disconnecting was: %11.

20200

RemoteAccess

The user: %1 connected on port: %2 has been assigned address: %3

20201

RemoteAccess

The user with IP address: %1 has disconnected.

20250

RemoteAccess

The user: %1 has connected and has been successfully authenticated on port: %2.

20251

RemoteAccess

The user: %1 connected on port: %2 on: %3 at: %4 and disconnected on: %5 at: %6. The user was active for: %7 minutes, %8 seconds. %9 bytes were sent and %10 bytes were received. The port speed was: %11. The reason for disconnecting was: %12.

20254

RemoteAccess

The user: %1 on port: %2 was called back at the number: %3.

20263

RemoteAccess

The port: %1 has been disconnected due to inactivity.

20264

RemoteAccess

The port: %1 has been disconnected because the user reached the maximum connect time allowed by the administrator.

20265

RemoteAccess

The user: %1 has connected and has been successfully authenticated on port: %2. Data sent and received over this link is encrypted.

20266

RemoteAccess

The user: %1 has connected and has been successfully authenticated on port: %2. Data sent and received over this link is strongly encrypted.

20267

RemoteAccess

The user: %1 has successfully established a connection to: %2 using the device: %3.

20268

RemoteAccess

The connection to: %1 made by user: %2 using device: %3 was disconnected.

20272

RemoteAccess

The user: %1 connected on port: %2 on: %3 at: %4 and disconnected on: %5 at: %6. The user was active for: %7 minutes %8 seconds. %9 bytes were sent and %10 bytes were received. The reason for disconnecting was: %11.

20274

RemoteAccess

The user: %1 connected on port: %2 has been assigned address: %3

20275

RemoteAccess

The user with IP address: %1 has disconnected.

RRAS Server

Routing and Remote Access Service Infrastructure