Windows Server
Portugal (Português) Iniciar sessão
Home Windows Server 2012 Windows Server 2008 R2 Windows Server 2003 Library Forums
Este tópico ainda não foi classificado - Classificar este tópico

IP Configuration Migration Guide

Actualizado: Abril de 2009

Aplica-se a: Windows Server 2008 R2

Migration of IP configuration data is a necessity for the migration of some server roles to Windows Server® 2008 R2, including DHCP Server, Domain Name System (DNS) Server, and Serviços do domínio Active Directory®. This guide describes how to migrate core IPv4 and IPv6 configuration settings and data.

The following table indicates the Windows Server operating systems that are supported by Ferramentas de Migração do Windows Server.

 

Source server processor Source server operating system Destination server operating system Destination server processor

x86- or x64-based

Windows Server 2003 with Service Pack 2

Windows Server 2008 R2, both full and Server Core installation options

x64-based

x86- or x64-based

Windows Server 2003 R2

Windows Server 2008 R2, both full and Server Core installation options

x64-based

x86- or x64-based

Full installation option of Windows Server 2008

Windows Server 2008 R2, both full and Server Core installation options

x64-based

x64-based

Windows Server 2008 R2, both full and Server Core installation options

Windows Server 2008 R2, both full and Server Core installation options

x64-based

The versions of operating systems shown in the preceding table are the oldest combinations of operating systems and service packs that are supported. Newer service packs, if available, are supported.

Foundation, Standard, Enterprise, and Datacenter editions of Windows Server are supported as either source or destination servers.

Migrations between physical operating systems and virtual operating systems are supported.

Ferramentas de Migração do Windows Server does not support migration from a source server to a destination server that is running an operating system in a different system UI language (that is, the installed language) than the source server. For example, you cannot use Ferramentas de Migração do Windows Server to migrate roles, operating system settings, data, or shares from a computer that is running Windows Server 2008 in the French system UI language to a computer that is running Windows Server 2008 R2 in the German system UI language.

noteNota
The system UI language is the language of the localized installation package that was used to set up the Windows operating system.

Both x86- and x64-based migrations are supported for Windows Server 2003 and Windows Server 2008 R2. All editions of Windows Server 2008 R2 are x64-based.

Roles that are running on Server Core installations of Windows Server 2008 cannot be migrated, because there is no .NET Framework available on Server Core installations of Windows Server 2008.

Ferramentas de Migração do Windows Server supports migration of the following frequently used IP configuration settings and data. Settings are migrated in the order in which they are listed in the Windows interface. For example, DNS server settings are migrated in the order in which they are used.

 

Setting type Supported settings and notes

Manually-configured IP settings for all enabled network adapters (also known as network interface cards, or NICs) that are connected to the network

IPV4 addresses

IPV4 subnet mask

IPV4 DHCP status

IPV4 default gateway addresses (but not gateway metrics)

IPV4 interface metric

IPV4 Windows Internet Name Service (WINS) server settings

  • WINS server addresses

  • NetBIOS setting (Default, Enable NetBIOS over TCP/IP, or Disable NetBIOS over TCP/IP)

IPV6 addresses and corresponding subnet prefix lengths

noteNota
Migration of IPV6 subnet prefix lengths is supported only on destination servers that are running Windows Server 2008 or Windows Server 2008 R2. If an IPV6 address is imported from a Windows Server 2003 migration store, the subnet prefix length is set to the default value of 64 on the destination server.

IPV6 router discovery setting

IPV6 Managed address configuration flag, and Other stateful configuration flag

noteNota
These settings are supported only on Windows Server 2008 and Windows Server 2008 R2. Windows Server 2003 does not support DHCPv6-based IPv6 address configuration.

If Router Discovery is enabled on the source server, you must ensure that the Advertising setting is the same on both source and destination servers to make sure that Managed address configuration and Other stateful configuration values are configured the same on both source and destination servers.

For example, if Managed address configuration is configured automatically on the source server, then the value for the Advertising setting must be the same on both source and destination servers for Managed address configuration to be configured automatically on the destination server.

Managed address configuration and Other stateful configuration settings are not imported to the destination server if they are configured as Automatic. In other words, they are not imported if the Router Discovery setting is enabled, yet the Advertising setting is disabled.

IPv6 default gateway addresses (but not gateway metrics)

IPv6 interface metric

noteNota
IPv6 interface metric is supported only on Windows Server 2008 and Windows Server 2008 R2. If this setting is manually configured on Windows Server 2003 or Windows Server 2003 R2, it will not be migrated. For more information about how to migrate this setting manually from Windows Server 2003 or Windows Server 2003 R2, see IP Configuration: Appendix.

DNS settings

  • IPV4 DNS server addresses

  • IPV6 DNS server addresses

  • DNS suffix for this connection

  • Register this connection’s addresses in DNS

  • Use this connection’s DNS suffix in DNS registration

For global (Windows-based) IP configuration
  • For resolution of unqualified names:

    • Append primary and connection-specific DNS suffixes

    • Append parent suffixes of the primary DNS suffixes

    • Append these DNS suffixes and the list of DNS suffixes (also known as the DNS search list)

Enable LMHOSTS lookup (but not LMHOSTS file)

IPv6 DisabledComponents property

noteNota
This setting is supported only on Windows Server 2008 and Windows Server 2008 R2. If this setting is configured in Windows Server 2003 or Windows Server 2003 R2, it will not be migrated. For more information about the DisabledComponents property, see “How to disable certain IP version 6 (IPv6) components in Windows Vista” on the Microsoft Web site.)

Group Policy settings or other autoconfigured settings related to IP configuration are not supported.

If the source server uses additional settings for advanced IP configuration that are not in the previous list, define a custom migration procedure based on the configuration of your organization’s network environment.

For more information about IP configuration settings that are not supported, see IP Configuration: Appendix.

Consultar Também

Considera isto útil?
(1500 caracteres restantes)

Conteúdo da Comunidade

Adicionar
© 2013 Microsoft
|
Comentários ao Site
© 2013 Microsoft. Todos os direitos reservados.