Share via


Netsh commands for Interface IP

Applies To: Windows Server 2003, Windows Server 2003 R2, Windows Server 2003 with SP1, Windows Server 2003 with SP2

Netsh commands for Interface IP

You can use commands in the Netsh Interface IP context to configure the TCP/IP protocol (including addresses, default gateways, DNS servers, and WINS servers) and to display configuration and statistical information.

You can run these commands from the Windows Server 2003 family command prompt or from the command prompt for the Netsh interface IP context. For these commands to work at the Windows Server 2003 family command prompt, you must type netsh interface ip before typing commands and parameters as they appear in the syntax below. There might be functional differences between Netsh context commands on Windows 2000 and the Windows Server 2003 family.

For more information on Netsh, see Netsh overview and Enter a netsh context.

To view the command syntax, click a command:

  • set address

  • add address

  • delete address

  • show address

  • set dns

  • add dns

  • delete dns

  • show dns

  • set wins

  • add wins

  • delete wins

  • show wins

  • show icmp

  • show interface

  • show ipaddress

  • show ipnet

  • show ipstats

  • show joins

  • show tcpconn

  • show tcpstats

  • show udpconn

  • show udpstats

  • show config

  • show offload

  • delete arpcache

  • dump

set address

Configures an IP address and a default gateway on a specified interface.

Syntax

set address [name=]InterfaceName [source=]{dhcp | static [addr=]IPAddress[mask=]SubnetMask [gateway=]{none | DefaultGateway [[gwmetric=]GatewayMetric]}}

Parameters
  • [ name =] InterfaceName
    Required. Specifies the name of the interface for which you want to configure address and gateway information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").
  • [ source=]{ dhcp| static[ addr=] IPAddress[ mask=] SubnetMask[ gateway=]{ none| DefaultGateway[[ gwmetric=] GatewayMetric]}}
    Required. Specifies whether the IP address to configure originates from a Dynamic Host Configuration Protocol (DHCP) server or is static. If the address is static, IPAddress specifies the address to configure, and SubnetMask specifies the subnet mask for the IP address being configured. If the address is static, you must also specify whether you want to leave the current default gateway (if any) in place or configure one for the address. If you configure a default gateway, DefaultGateway specifies the IP address of the default gateway to be configured, and GatewayMetric specifies the metric for the default gateway to be configured.
  • /?
    Displays help at the command prompt.
Remarks
  • You can use this command to switch an interface between DHCP configuration and static configuration. If the interface is configured statically, the DNS and WINS server addresses for this interface must also be statically configured.

  • Omitting the DefaultGateway parameter does not clear gateway configuration but preserves whatever was previously configured.

add address

Adds an IP address and a default gateway on a specified interface configured with a static IP address.

Syntax

add address [name=]InterfaceName [addr=]IPAddress [mask=]SubnetMask[[gateway=] DefaultGateway [gwmetric=]GatewayMetric]

Parameters
  • [ name=] InterfaceName
    Required. Specifies the name of the interface for which you want to add address and gateway information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").
  • [ addr=] IPAddress[ mask=] SubnetMask
    Required. Specifies the IP address to add and the subnet mask for that IP address.
  • [ gateway=] DefaultGateway[ gwmetric=] GatewayMetric
    Specifies the IP address of the default gateway to add and the metric for that default gateway.
  • /?
    Displays help at the command prompt.

delete address

Deletes an IP address or a default gateway on a statically configured interface.

Syntax

delete address [name=]InterfaceName [addr=] IPAddress [[gateway=]{DefaultGateway | all}]

Parameters
  • [ name=] InterfaceName
    Required. Specifies the name of the interface for which you want to delete address and gateway information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").
  • [ addr=] IPAddress
    Required. Specifies the IP address to delete.
  • [ gateway=]{ DefaultGateway| all}
    Specifies whether to delete one default gateway or all default gateways. If only one default gateway should be deleted, DefaultGateway specifies the IP address of the default gateway to be deleted.
  • /?
    Displays help at the command prompt.
Remarks
  • This command will not delete the last IP address on the interface.

show address

Displays information about static IP addresses and default gateways on a specified interface. Used without parameters, show address displays address information for all interfaces.

Syntax

show address [[name=]InterfaceName]

Parameters
  • [ name=] InterfaceName
    Specifies the name of the interface for which you want to display address information. The InterfaceName must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").
  • /?
    Displays help at the command prompt.
Remarks
  • For interfaces configured using DHCP, use the ipconfig command to display the assigned IP addresses, lease parameters, and other DHCP information.

set dns

Configures a DNS server address for a specified interface.

Syntax

set dns [name=]InterfaceName [source=]{dhcp | static }[addr=]{IP Address | none} [register=]{none | primary | both}

Parameters
  • [ name=] InterfaceName
    Required. Specifies the name of the interface for which you want to set DNS information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").
  • [ source=]{ dhcp| static }
    Required. Specifies whether the IP address of the DNS server is configured by DHCP or is static.
  • [ addr=]{ IP Address| none }
    If the IP address is static, IP Address specifies the IP address of the DNS server to configure, and none specifies that the DNS configuration should be removed.
  • [ register=]{ none| primary| both }
    None specifies whether to disable Dynamic DNS resolution. Primary registers the computer name under the primary DNS suffix only. Both registers the computer name under both the primary DNS suffix as well as under the connection-specific suffix.
  • /?
    Displays help at the command prompt.
Remarks
  • If the interface is already statically configured, the static parameter replaces the existing list of DNS server addresses with the one specified in the command.

  • Only if the [source] is static is the [addr] option available for configuring a static list of DNS server IP addresses for the specified interface.

Examples

set dns name="Local Area Connection" source=dhcp

set dns "Local Area Connection" static 10.0.0.1 primary

add dns

Adds a DNS server to a list of DNS servers for a specified interface.

Syntax

add dns [name=]InterfaceName [addr=] DNSAddress [[index=]DNSIndex]

Parameters
  • [ name=] InterfaceName
    Required. Specifies the name of the interface for which you want to add DNS information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").
  • [ addr=] DNSAddress
    Required. Specifies the IP address of the DNS server to add.
  • [ index=] DNSIndex
    Specifies the position of the added DNS server in the list of DNS servers for the interface.
  • /?
    Displays help at the command prompt.
Remarks
  • A lower number for the DNSIndex parameter corresponds to a higher preference. If no index is specified, then the server is added with the lowest preference.

delete dns

Deletes a DNS server or all DNS servers from a list of DNS servers for a specified interface or for all interfaces.

Syntax

delete dns [name=]InterfaceName [addr=]{DNSAddress | all}

Parameters
  • [ name=] InterfaceName
    Required. Specifies the name of the interface for which you want to delete DNS information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").
  • [ addr=]{ DNSAddress| all}
    Required. Specifies whether to delete the address of one DNS server or all servers for all interfaces. If only one DNS server should be deleted, DNSAddress specifies the IP address of the DNS server to delete.
  • /?
    Displays help at the command prompt.

show dns

Displays the DNS configuration of a specified interface. Used without parameters, show dns displays the DNS configurations of all interfaces.

Syntax

show dns [[name=]InterfaceName]

Parameters
  • [ name=] InterfaceName
    Specifies the name of the interface whose DNS configuration you want to display. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").
  • /?
    Displays help at the command prompt.

set wins

Sets WINS server configuration to either DHCP or static mode for a specified interface.

Syntax

set wins [name=]InterfaceName [source=]{dhcp | static [addr=]{WINSAddress | none }}

Parameters
  • [ name=] InterfaceName
    Required. Specifies the name of the interface for which you want to set WINS information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").
  • [ source=]{ dhcp| static[ addr=]{ WINSAddress| none}}
    Required. Specifies whether the IP address of the WINS server to configure should be assigned by DHCP or is static. If the IP address is static, WINSAddress specifies the IP address of the WINS server to configure, and none specifies that the WINS configuration should be removed.
  • /?
    Displays help at the command prompt.
Remarks
  • If the interface is already statically configured, the static parameter replaces the existing WINS server address list with the one specified in the set wins command.

add wins

Adds a WINS server to a list of WINS servers for a specified interface.

Syntax

add wins [name=]InterfaceName [addr=] WINSAddress [[index=]WINSIndex]

Parameters
  • [ name=] InterfaceName
    Required. Specifies the name of the interface for which you want to add WINS information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").
  • [ addr=] WINSAddress
    Required. Specifies the IP address of the WINS server to add.
  • [ index=] WINSIndex
    Specifies the position of the added WINS server in the WINS server list for that interface.
  • /?
    Displays help at the command prompt.
Remarks
  • A lower number for the WINSIndex parameter corresponds to a higher preference. If no index is specified, then the server is added with the lowest preference.

delete wins

Deletes a WINS server or servers from a list of WINS servers for a specified interface or all interfaces.

Syntax

delete wins [name=]InterfaceName [addr=]{WINSAddress | all}

Parameters
  • [ name=] InterfaceName
    Required. Specifies the name of the interface for which you want to delete a WINS server or servers. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").
  • [ addr=]{ WINSAddress| all}
    Required. Specifies whether to delete only one server for an interface or all servers for all interfaces. If only one server should be deleted, WINSAddress specifies the IP address of the WINS server to delete.
  • /?
    Displays help at the command prompt.

show wins

Displays the WINS configuration for a specified interface. Used without parameters, show wins displays the WINS configuration for all interfaces.

Syntax

show wins [[name=]InterfaceName]

Parameters
  • [ name=] InterfaceName
    Specifies the name of the interface whose WINS information you want to display. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").
  • /?
    Displays help at the command prompt.

show icmp

Displays ICMP statistics. Used without parameters, show icmp displays the statistics only once.

Syntax

show icmp [[rr=]RefreshRate]

Parameters
  • [ rr=] RefreshRate
    Specifies the refresh rate (the number of seconds between refreshing the display of the statistics).
  • /?
    Displays help at the command prompt.

show interface

Displays statistics for a specified interface. Used without parameters, show interface displays statistics for all interfaces only once.

Syntax

show interface [[index=]InterfaceIndex] [[rr=]RefreshRate]

Parameters
  • [ index=] InterfaceIndex
    Specifies the interface index, an integer that identifies the interface.
  • [ rr=] RefreshRate
    Specifies the refresh rate (the number of seconds between refreshing the display of the statistics).
  • /?
    Displays help at the command prompt.
Remarks
  • To obtain the interface index for an interface, review the output of the show interface command used without parameters.

show ipaddress

Displays information for a specified IP address. Used without parameters, show ipaddress displays information for all IP addresses on all interfaces once.

Syntax

show ipaddress [[index=]IPAddress] [[rr=]RefreshRate]

Parameters
  • [ index=] IPAddress
    Specifies an IP address of an interface.
  • [ rr=] RefreshRate
    Specifies the refresh rate (the number of seconds between refreshing the display of the statistics).
  • /?
    Displays help at the command prompt.
Remarks
  • To obtain the IP addresses of all interfaces, review the display of the show ipaddress command used without parameters.

show ipnet

Displays the contents of the Address Resolution Protocol (ARP) cache, which contains the hardware addresses of resolved next-hop IP addresses. Used without parameters, show ipnet displays the information once.

Syntax

show ipnet [[rr=]RefreshRate]

Parameters
  • [ rr=] RefreshRate
    Specifies the refresh rate (the number of seconds between refreshing the display of the statistics).
  • /?
    Displays help at the command prompt.

show ipstats

Displays IP statistics. Used without parameters, show ipstats displays the statistics once.

Syntax

show ipstats [[rr=]RefreshRate]

Parameters
  • [ rr=] RefreshRate
    Specifies the refresh rate (the number of seconds between refreshing the display of the statistics).
  • /?
    Displays help at the command prompt.

show joins

Displays IP multicast groups that have been joined for the specified IP address. Used without parameters, show joins displays information for all IP addresses.

Syntax

show joins [[index=]IPAddress]

Parameters
  • [ index=] IPAddress
    Specifies an IP address of an interface.
  • /?
    Displays help at the command prompt.
Remarks
  • To obtain the IP addresses for all interfaces, review the display of the show ipaddress command used without parameters.

show tcpconn

Displays information on a specified TCP connection. Used without parameters, show tcpconn displays information for all TCP connections once.

Syntax

show tcpconn [[index=]{LocalIPAddress | LocalPort | RemoteIPAddress | RemotePort}] [[rr=]RefreshRate]

Parameters
  • [ index=]{ LocalIPAddress| LocalPort| RemoteIPAddress| RemotePort}
    Specifies the connection about which to display information. The LocalIPAddress parameter specifies an IP address of an interface. The LocalPort parameter specifies a TCP port for a local process. The RemoteIPAddress parameter specifies an IP address of a remote host. The RemotePort parameter specifies a TCP port for a remote process.
  • [ rr=] RefreshRate
    Specifies the refresh rate (the number of seconds between refreshing the display of the information).
  • /?
    Displays help at the command prompt.

show tcpstats

Displays TCP statistics. Used without parameters, show tcpstats displays the statistics once.

Syntax

show tcpstats [[rr=]RefreshRate]

Parameters
  • [ rr=] RefreshRate
    Specifies the refresh rate (the number of seconds between refreshing the display of the statistics).
  • /?
    Displays help at the command prompt.

show udpconn

Displays information about the UDP ports used for each IP address. Used without parameters, show udpconn displays UDP port information for all IP addresses once.

Syntax

show udpconn [[index=]{LocalIPAddress | LocalPort}] [[rr=]RefreshRate]

Parameters
  • [ index=]{ LocalIPAddress| LocalPort}
    Specifies the connection about which to display information. The LocalIPAddress parameter specifies an IP address of an interface. The LocalPort parameter specifies a UDP port for a local process.
  • [ rr=] RefreshRate
    Specifies the refresh rate (the number of seconds between refreshing the display of the statistics).
  • /?
    Displays help at the command prompt.

show udpstats

Displays UDP statistics. Used without parameters, show udpstats displays the statistics once.

Syntax

show udpstats [[rr=]RefreshRate]

Parameters
  • [ rr=] RefreshRate
    Specifies the refresh rate (the number of seconds between refreshing the display of the statistics).
  • /?
    Displays help at the command prompt.

show config

Displays IP address and other configuration information for a specified interface. Used without parameters, show config displays configuration information for all interfaces.

Syntax

show config [[name=]InterfaceName]

Parameters
  • [ name=] InterfaceName
    Specifies the name of the interface for which you want to display configuration information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").
  • /?
    Displays help at the command prompt.

show offload

Displays the tasks that can be performed by the network adapter for the specified interface corresponding to installed network hardware. Used without parameters, show offload displays offload information for all interfaces corresponding to installed network hardware.

Syntax

show offload [[name=]InterfaceName ]

Parameters
  • [ name=] InterfaceName
    Specifies the name of the interface for which you want to display offload information. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").
  • /?
    Displays help at the command prompt.

delete arpcache

Removes the entries in the Address Resolution Protocol (ARP) cache for a specified interface. Used without parameters, delete arpcache removes the entries in the ARP caches of all interfaces.

Syntax

delete arpcache [[name=]InterfaceName]

Parameters
  • [ name=] InterfaceName
    Specifies the name of the interface for which you want to remove the ARP cache entries. The InterfaceName parameter must match the name of the interface as specified in Network Connections. If InterfaceName contains spaces, use quotation marks around the text (for example, "Interface Name").
  • /?
    Displays help at the command prompt.

dump

Displays the current configuration as a series of Netsh Interface IP commands.

Syntax

dump

Parameters

none

Remarks
  • To create a configuration script file, redirect the output of this command to a file.

Netsh Interface IP example

The following command configures the interface named Local Area Connection with the static IP address 10.0.5.99, the subnet mask of 255.255.255.0, and a default gateway of 10.0.5.1:

set address name="Local Area Connection" source=static addr=10.0.5.99 mask=255.255.255.0 gateway=10.0.5.1 gwmetric=1

Formatting legend

Format Meaning

Italic

Information that the user must supply

Bold

Elements that the user must type exactly as shown

Ellipsis (...)

Parameter that can be repeated several times in a command line

Between brackets ([])

Optional items

Between braces ({}); choices separated by pipe (|). Example: {even|odd}

Set of choices from which the user must choose only one

Courier font

Code or program output

See Also

Concepts

Netsh commands for AAAA
Netsh commands for DHCP
Netsh diagnostic (diag) commands
Netsh commands for remote access (ras)
Netsh commands for WINS
Command-line reference A-Z
Command shell overview