Set-ADSite

This cmdlet is available only in on-premises Exchange.

Use the Set-AdSite cmdlet to configure the Exchange settings of Active Directory sites.

For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.

Syntax

Set-ADSite
   [-Identity] <AdSiteIdParameter>
   [-Confirm]
   [-DomainController <Fqdn>]
   [-HubSiteEnabled <Boolean>]
   [-InboundMailEnabled <Boolean>]
   [-PartnerId <Int32>]
   [-WhatIf]
   [<CommonParameters>]

Description

You need to be assigned permissions before you can run this cmdlet. Although this topic lists all parameters for the cmdlet, you may not have access to some parameters if they're not included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.

Examples

Example 1

Set-AdSite Default-First-Site-Name -HubSiteEnabled $true

This example configures the Active Directory site named Default-First-Site-Name as a hub site.

Parameters

-Confirm

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

  • Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
  • Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
Type:SwitchParameter
Aliases:cf
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-DomainController

The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.

Type:Fqdn
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-HubSiteEnabled

The HubSiteEnabled parameter specifies whether this site acts as a hub site. The default value is $false.

Type:Boolean
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-Identity

The Identity parameter specifies the identity of the Active Directory site you want to modify. You can use any value that uniquely identifies the site. For example, you can use the name, GUID or distinguished name (DN) of the Active Directory site.

Type:AdSiteIdParameter
Position:1
Default value:None
Required:True
Accept pipeline input:True
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-InboundMailEnabled

The InboundMailEnabled parameter enables or disables receiving incoming messages for all the Exchange located in the Active Directory site. Typically, this parameter is used after Active Directory site failover or maintenance.

Valid input for this parameter is $true or $false. The default value is $true. If you set the value to $false, none of the Exchange servers in the Active Directory site will be able to receive incoming messages.

Type:Boolean
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-PartnerId

This parameter is reserved for internal Microsoft use.

Type:Int32
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-WhatIf

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.

Type:SwitchParameter
Aliases:wi
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

Inputs

Input types

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn't accept input data.

Outputs

Output types

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn't return data.