New-UMIPGateway

This cmdlet is available only in on-premises Exchange.

Use the New-UMIPGateway cmdlet to create a Unified Messaging (UM) IP gateway. A UM IP gateway is used to connect Unified Messaging servers to an IP gateway or a Session Initiation Protocol (SIP)-enabled IP Private Branch eXchange (PBX).

For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.

Syntax

New-UMIPGateway
   [-Name] <String>
   -Address <UMSmartHost>
   [-Confirm]
   [-DomainController <Fqdn>]
   [-IPAddressFamily <IPAddressFamily>]
   [-UMDialPlan <UMDialPlanIdParameter>]
   [-WhatIf]
   [<CommonParameters>]

Description

A UM IP gateway has organization-wide scope and references a single physical IP gateway. The UM IP gateway that's created is used to establish a connection to an IP gateway or a SIP-enabled IP PBX. After this task is completed, a new UM IP gateway is created.

This cmdlet is scheduled to be removed from Exchange Online on December 1, 2019. For more information, see this blog post.

You need to be assigned permissions before you can run this cmdlet. Although this topic lists all parameters for the cmdlet, you may not have access to some parameters if they're not included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.

Examples

Example 1

New-UMIPGateway -Identity MyUMIPGateway -Address 10.10.10.1

This example creates the UM IP gateway MyUMIPGateway that enables a Mailbox server to start accepting calls from an IP gateway with an IP address of 10.10.10.1.

Example 2

New-UMIPGateway -Identity MyUMIPGateway -Address fe80::39bd:88f7:6969:d223%11 -IPAddressFamily Any

This example creates the UM IP gateway MyUMIPGateway with an IPv6 address and allows the UM IP gateway to use IPv4 and IPV6 addresses.

Example 3

New-UMIPGateway -Identity MyUMIPGateway -Address "MyUMIPGateway.contoso.com"

This example creates the UM IP gateway MyUMIPGateway that enables a Mailbox server to start accepting calls from an IP gateway with an FQDN of MyUMIPGateway.contoso.com.

Parameters

-Address

The Address parameter specifies the IP address configured on the IP gateway or SIP-enabled IP PBX.

Type:UMSmartHost
Position:Named
Default value:None
Required:True
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016

-Confirm

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

  • Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
  • Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
Type:SwitchParameter
Aliases:cf
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016

-DomainController

This parameter is available only in on-premises Exchange.

The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.

Type:Fqdn
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016

-IPAddressFamily

The IPAddressFamily parameter specifies whether the UM IP gateway will use Internet Protocol version 4 (IPv4), IPv6, or both to communicate. Valid values are:

  • IPv4Only: The UM IP gateway will only use IPv4 to communicate. This is the default value.
  • IPv6Only: The UM IP gateway will only use IPv6.
  • Any: IPv6 will be used first, and then if necessary, it will fall back to IPv4.
Type:IPAddressFamily
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2013, Exchange Server 2016

-Name

The Name parameter specifies the display name for the UM IP gateway. The name for the new UM IP gateway can contain up to 64 characters.

Type:String
Position:1
Default value:None
Required:True
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016

-UMDialPlan

The UMDialPlan parameter specifies the UM dial plan to be associated with the UM IP gateway.

Type:UMDialPlanIdParameter
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016

-WhatIf

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.

Type:SwitchParameter
Aliases:wi
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016

Inputs

Input types

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn't accept input data.

Outputs

Output types

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn't return data.