Any suggestions? Export (0) Print
Expand All
Collapse the table of content
Expand the table of content
Expand Minimize

Add-IPAllowListEntry

 

Applies to: Exchange Server 2016

This cmdlet is available or effective only on Edge Transport servers in on-premises Exchange Server 2016.

Use the Add-IPAllowListEntry cmdlet to add IP Allow list entries to the IP Allow list that's used by the Connection Filtering agent on Edge Transport servers.

Add-IPAllowListEntry -IPRange <IPRange> <COMMON PARAMETERS>
Add-IPAllowListEntry -IPAddress <IPAddress> <COMMON PARAMETERS>
COMMON PARAMETERS: [-Comment <String>] [-Confirm [<SwitchParameter>]] [-ExpirationTime <DateTime>] [-Server <ServerIdParameter>] [-WhatIf [<SwitchParameter>]]

This example adds the IP address 192.168.0.100 to the list of allowed IP addresses.

Add-IPAllowListEntry -IPAddress 192.168.0.100

This example adds the IP address range 192.168.0.1/24 to the list of allowed IP addresses and configures the IP Allow list entry to expire at 23:59 on January 3, 2013.

Add-IPAllowListEntry -IPRange 192.168.0.1/24 -ExpirationTime "1/3/2013 23:59"

You need to be assigned permissions before you can run this cmdlet. Although all parameters for this cmdlet are listed in this topic, you may not have access to some parameters if they're not included in the permissions assigned to you. To see what permissions you need, see the "Anti-spam features - Edge Transport" entry in the Anti-spam and anti-malware permissions topic.

 

Parameter Required Type Description

IPAddress

Required

System.Net.IPAddress

The IPAddress parameter specifies a single IP address to add to the IP Allow list, for example, 192.168.0.1.

IPRange

Required

Microsoft.Exchange.Data.IPRange

The IPRange parameter specifies a range of IP addresses to add to the IP Allow list. You can use the following formats:

  • CIDR IP    192.168.0.1/24

  • IP address range   192.168.0.1-192.168.0.254.

Comment

Optional

System.String

The Comment parameter specifies an optional comment. If you specify a value that contains spaces, enclose the value in quotation marks ("), for example: "This is an admin note".

Confirm

Optional

System.Management.Automation.SwitchParameter

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

  • Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.

  • Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.

ExpirationTime

Optional

System.DateTime

The ExpirationTime parameter specifies a day and time when the IP Allow list entry that you're creating will expire. If you specify a time only, and you don't specify a date, the current day is assumed.

Use the short date format that's defined in the Regional Options settings on the computer where you're running the command. For example, if the computer is configured to use the short date format mm/dd/yyyy, enter 09/01/2015 to specify September 1, 2015. You can enter the date only, or you can enter the date and time of day. If you enter the date and time of day, enclose the value in quotation marks ("), for example, "09/01/2015 5:00 PM".

Server

Optional

Microsoft.Exchange.Configuration.Tasks.ServerIdParameter

The Server parameter specifies the Exchange server where you want to run this command. You can use any value that uniquely identifies the server. For example:

  • Name

  • FQDN

  • Distinguished name (DN)

  • Exchange Legacy DN

If you don't use this parameter, the command is run on the local server.

You can't use this parameter to configure other Edge Transport servers remotely.

WhatIf

Optional

System.Management.Automation.SwitchParameter

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn’t accept input data.

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn’t return data.

 
Show:
© 2016 Microsoft