Use Telnet to test SMTP communication

Applies to: Exchange Server 2013

This topic explains how to use Telnet to test Simple Mail Transfer Protocol (SMTP) communication between messaging servers. By default, SMTP listens on port 25. If you use Telnet on port 25, you can enter the SMTP commands that are used to connect to an SMTP server and send a message exactly as if your Telnet session was an SMTP messaging server. You can see the success or failure of each step in the connection and message submission process.

Here are the scenarios where you may want to use Telnet to test SMTP communication to or from the transport servers that exist in your Microsoft Exchange organization:

• Connect to your organization's Internet-facing Exchange server from a host that is located outside your perimeter network and send a test message.
• Connect to a remote messaging server from your organization's Internet-facing Exchange server and send a test message.

The procedure in this topic shows you how to use Telnet Client, which is a component that is included with Microsoft Windows. Third-party Telnet clients may require a syntax that is different from that of the Windows Telnet component.

• Estimated time to complete: 30 minutes

• Exchange permissions don't apply to the procedures in this topic. These procedures are performed in the operating system of the Exchange Server or a client computer.

• The procedures in this topic are best used to connect to and from Internet-facing servers that allow anonymous connections. Message transmission between internal Exchange servers is encrypted and authenticated. To use Telnet to connect to the Hub Transport service on a Mailbox server, you'll need to create a Receive connector that's configured to allow anonymous access or Basic authentication to receive messages. If the connector allows Basic authentication, you need a utility to convert the text strings that are used for the username and password into the Base64 format. Because the username and password are easily discernible when Basic authentication is used, we don't recommend Basic authentication without encryption.

• If you connect to a remote messaging server, consider performing the procedures in this topic on your Internet-facing Exchange server. This will help to avoid rejection of the test message by remote messaging servers that are configured to validate the source IP address, the corresponding domain name system (DNS) domain name, and the reverse lookup IP address of any Internet host that tries to send a message to the server.

• For information about keyboard shortcuts that may apply to the procedures in this topic, see Keyboard shortcuts in the Exchange admin center.

By default, the Telnet Client isn't installed in most client or server versions of the Microsoft Windows operating systems. To install it, see Install Telnet Client.

To connect to a destination SMTP server by using Telnet on port 25, you must use the fully qualified domain name (FQDN) or the IP address of the SMTP server. If the FQDN or IP address is unknown, the easiest way to find this information is to use the Nslookup command-line tool to find the MX record for the destination domain.

1. At a command prompt, type nslookup, and then press ENTER. This command opens the Nslookup session.

2. Type set type=mx and then press ENTER.

3. Type set timeout=20 and then press ENTER. By default, Windows DNS servers have a 15-second recursive DNS query time-out limit.

4. Type the name of the domain for which you want to find the MX record. For example, to find the MX record for the fabrikam.com domain, type fabrikam.com., and then press ENTER.

   Note

   The trailing period ( . ) indicates a FQDN. The use of the trailing period prevents any default DNS suffixes that are configured for your network from being unintentionally added to the domain name.

   The output of the command will resemble the following:

   fabrikam.com mx preference=10, mail exchanger = mail1.fabrikam.com
   fabrikam.com mx preference=20, mail exchanger = mail2.fabrikam.com
   mail1.fabrikam.com internet address = 192.168.1.10
   mail2 fabrikam.com internet address = 192.168.1.20
   

   You can use any of the host names or IP addresses that are associated with the MX records as the destination SMTP server. A lower value of preference indicates a preferred SMTP server. You can use multiple MX records and different values of preference for load balancing and fault tolerance.

5. When you're ready to end the Nslookup session, type exit, and then press ENTER.

In this example, the following values are used:

• Destination SMTP server: mail1.fabrikam.com
• Source domain: contoso.com
• Sender's e-mail address: chris@contoso.com
• Recipient's e-mail address: kate@fabrikam.com
• Message subject: Test from Contoso
• Message body: This is a test message

500 5.3.3 Unrecognized command

1. At a command prompt, type telnet, and then press ENTER. This command opens the Telnet session.

2. Type set localecho and then press ENTER. This optional command lets you view the characters as you type them. This setting may be required for some SMTP servers.

3. Type set logfile <filename>. This optional command enables logging of the Telnet session to the specified log file. If you only specify a file name, the location of the log file is the current working directory. If you specify a path and a file name, the path must be local to the computer. Both the path and the file name that you specify must be entered in the Microsoft DOS 8.3 format. The path that you specify must already exist. If you specify a log file that doesn't exist, it will be created for you.

4. Type open mail1.fabrikam.com 25 and then press ENTER.

5. Type EHLO contoso.com and then press ENTER.

6. Type MAIL FROM:chris@contoso.com and then press ENTER.

7. Type RCPT TO:kate@fabrikam.com NOTIFY=success,failure and then press ENTER. The optional NOTIFY command defines the particular delivery status notification (DSN) messages that the destination SMTP server must provide to the sender. DSN messages are defined in RFC 1891. In this case, you're requesting a DSN message for successful or failed message delivery.

8. Type DATA and then press ENTER. You will receive a response that resembles the following:

   354 Start mail input; end with <CLRF>.<CLRF>
   

9. Type Subject: Test from Contoso and then press ENTER.

10. Press ENTER. RFC 2822 requires a blank line between the Subject: header field and the message body.

11. Type This is a test message and then press ENTER.

12. Press ENTER, type a period ( . ) and then press ENTER. You will receive a response that resembles the following:

    250 2.6.0 <GUID> Queued mail for delivery
    

13. To disconnect from the destination SMTP server, type QUIT and then press ENTER. You will receive a response that resembles the following:

    221 2.0.0 Service closing transmission channel
    

14. To close the Telnet session, type quit and then press ENTER.

This section provides information about responses that may be provided to the following commands, which were used in the previous example:

• Open mail1.fabrikam.com 25

• EHLO contoso.com

• MAIL FROM:chris@contoso.com

• RCPT TO:kate@fabrikam.com NOTIFY=success,failure

  Note

  The 3-digit SMTP response codes that are defined in RFC 2821 are the same for all SMTP messaging servers. The text descriptions may differ slightly for some SMTP messaging servers.

Successful Response: 220 mail1.fabrikam.com Microsoft ESMTP MAIL Service ready at <day-date-time>

Failure Response: Connecting to mail1.fabrikam.com...Could not open connection to the host, on port 25: Connect failed

Possible Reasons for Failure:

• The destination SMTP service is unavailable.
• There are restrictions on the destination firewall.
• There are restrictions on the source firewall.
• An incorrect FQDN or IP address for the destination SMTP server was specified.
• An incorrect port number was specified.

Successful Response: 250 mail1.fabrikam.com Hello [<sourceIPaddress>]

Failure Response: 501 5.5.4 Invalid domain name

Possible Reasons for Failure: There are invalid characters in the domain name. Alternatively, there are connection restrictions on the destination SMTP server.

Successful Response: 250 2.1.0 Sender OK

Failure Response: 550 5.1.7 Invalid address

Possible Reasons for Failure: There is a syntax error in the sender's e-mail address.

Failure Response: 530 5.7.1 Client was not authenticated

Possible Reasons for Failure: The destination server does not accept anonymous message submissions. You receive this error if you try to use Telnet to submit a message directly to a Hub Transport server.

Successful Response: 250 2.1.5 Recipient OK

Failure Response: 550 5.1.1 User unknown

Possible Reasons for Failure: The specified recipient does not exist in the organization.