WiFi configuration service provider

  • Article

September 30, 2015

The WiFi configuration service provider provides the functionality to add or delete Wi-Fi networks on a Windows Phone device. The configuration service provider accepts SyncML input and converts it to a network profile that is installed on the device. This profile enables the device to connect to the Wi-Fi network when it is in range.

Note

This CSP applies only to Windows Embedded 8.1 Handheld devices.

Important considerations:

  • If the authentication method needs a certificate, for example, EAP-TLS requires client certificates, you must configure it through the CertificateStore configuration service provider. The WiFi configuration service provider does not provide that functionality; instead, the Wi-Fi profile can specify characteristics of the certificate to be used for choosing the right certificate for that network. The server must successfully enroll the certificate first before deploying the Wi-Fi network configuration. For example, for an EAP-TLS profile, the server must successfully configure and enroll the required client certificate before deploying the Wi-Fi profile. Self-signed certificate works for EAP-TLS/PEAP-MSCHAPv2, but it is not supported in EAP-TLS.

  • Since the Windows Phone emulator does not support Wi-Fi, you cannot test the Wi-Fi configuration with an emulator. You can still provision a Wi-Fi network using the WiFi CSP, then check it in the Wi-Fi settings page, but you cannot test the network connectivity in the emulator.

  • For WEP, WPA, and WPA2-based networks, you should include the passkey in the network configuration in plaintext. The passkey is encrypted automatically when it is stored on the device.

  • WlanXml blob is sent in OMA SyncML XML message as chr. The profile XML content needs to be XML escaped in the OMA message.

  • The SSID of the Wi-Fi network part of the LocURI node must be a valid URI based on RFC 2396. This requires that all non-ASCII characters must be escaped using a %-character. Unicode characters without the necessary escaping are not supported.

  • The <name>name_goes_here</name><SSIDConfig> must match <SSID><name> name_goes_here</name></SSID>.

  • Windows Phone does not support EapHostUserCredentials for Enterprise Wi-Fi WlanXml blob.

The following image shows the WiFi configuration service provider in tree format as used by both the Open Mobile Alliance (OMA) Device Management (DM) and OMA Client Provisioning.

The following list shows the characteristics and parameters.

  • Profile
    Identifies the Wi-Fi network configuration. Each Wi-Fi network configuration is represented by a profile object. This network profile includes all the information required for the device to connect to that network – for example, the SSID, authentication and encryption methods and passphrase in case of WEP or WPA2 networks.

    Supported operation is Get.

  • <SSID>
    Specifies the name, 32 bytes maximum, of the Wi-Fi network to create, configure, query, or delete. The name is case sensitive and can be represented in ASCII. The SSID is added when the WlanXML node is added, and deleted when theWlanXml is deleted.

  • WlanXML
    The XML that describes the network configuration and follows the WLAN_profile Schema on MSDN.

    Supported operations are Get, Add, Delete, and Replace. Value type is chr. The profile XML must be escaped, as shown in the examples below.

    If it exists in the blob, the keyType and protected elements must come before keyMaterial, as shown in the example in WPA2-Personal Profile Sample.

  • Proxy
    A proxy server host and port can be specified per connection for Windows Phone. The format is host:port, where host can be one of the following:

    • a registered host name, such as server name, FQDN, or Single Label Name (SLN), such as myweb instead of myweb.contoso.com.

    • IPv4 address

    • IPv6/IPvFuture address

    If it is an IPvFuture address, then it must be specified as an IP literal as "[" (IP v6 address / IPvFuture ) "]", such as "[2441:4880:28:3:204:76ff:f43f:6eb]:8080".

    Supported operations are Get, Add, Delete, and Replace.

  • DisableInternetConnectivityChecks
    Optional. Specifies if the Wi-Fi SSID will be added to an IgnoreList and the network hijack check will be skipped for that SSID. If the parameter is not specified, the device will run the network hijack check.

    <parm name="DisableInternetConnectivityChecks" datatype="string" value="true" />

Examples

These XML examples show how to perform various tasks using OMA DM.

Add a network and no proxy

The following example shows how to add an open network with SSID ‘MyNetwork’ and no proxy.

<Atomic>
      <CmdID>300</CmdID>
      <Add>
        <CmdID>301</CmdID>
        <Item>
          <Target>
            <LocURI>./Vendor/MSFT/WiFi/Profile/MyNetwork/WlanXml</LocURI>
          </Target>
          <Meta>
            <Format xmlns="syncml:metinf">chr</Format>
          </Meta>
          <Data>&lt;?xml version=&quot;1.0&quot;?&gt;&lt;WLANProfile xmlns=&quot;https://www.microsoft.com/networking/WLAN/profile/v1&quot;&gt;&lt;name&gt;MyNetwork&lt;/name&gt;&lt;SSIDConfig&gt;&lt;SSID&gt;&lt;name&gt;MyNetwork&lt;/name&gt;&lt;/SSID&gt;&lt;/SSIDConfig&gt;&lt;connectionType&gt;ESS&lt;/connectionType&gt;&lt;connectionMode&gt;manual&lt;/connectionMode&gt;&lt;MSM&gt;&lt;security&gt;&lt;authEncryption&gt;&lt;authentication&gt;open&lt;/authentication&gt;&lt;encryption&gt;none&lt;/encryption&gt;&lt;/authEncryption&gt;&lt;/security&gt;&lt;/MSM&gt;&lt;/WLANProfile&gt; </Data>
        </Item>
      </Add>
</Atomic>

The following example shows how to add a WPA2 PSK network with SSID ‘My Network’ and no proxy.

<Atomic>
      <CmdID>300</CmdID>
      <Add>
        <CmdID>301</CmdID>
        <Item>
          <Target>
            <LocURI>./Vendor/MSFT/WiFi/Profile/MyNetwork/WlanXml</LocURI>
          </Target>
          <Meta>
            <Format xmlns="syncml:metinf">chr</Format>
          </Meta>
          <Data>&lt;?xml version=&quot;1.0&quot;?&gt;&lt;WLANProfile xmlns=&quot;https://www.microsoft.com/networking/WLAN/profile/v1&quot;&gt;&lt;name&gt;MyNetwork&lt;/name&gt;&lt;SSIDConfig&gt;&lt;SSID&gt;&lt;name&gt;MyNetwork&lt;/name&gt;&lt;/SSID&gt;&lt;/SSIDConfig&gt;&lt;connectionType&gt;ESS&lt;/connectionType&gt;&lt;connectionMode&gt;manual&lt;/connectionMode&gt;&lt;MSM&gt;&lt;security&gt;&lt;authEncryption&gt;&lt;authentication&gt;WPA2PSK&lt;/authentication&gt;&lt;encryption&gt;AES&lt;/encryption&gt;&lt;/authEncryption&gt;&lt;sharedKey&gt;&lt;keyType&gt;passPhrase&lt;/keyType&gt;&lt;protected&gt;false&lt;/protected&gt;&lt;keyMaterial&gt;123456789&lt;/keyMaterial&gt;&lt;/sharedKey&gt;&lt;/security&gt;&lt;/MSM&gt;&lt;/WLANProfile&gt; </Data>
        </Item>
      </Add>
</Atomic>

The following example shows how to add WPA PSK network with SSID ‘MyNetwork’ and no proxy.

<Atomic>
      <CmdID>300</CmdID>
      <Add>
        <CmdID>301</CmdID>
        <Item>
          <Target>
            <LocURI>./Vendor/MSFT/WiFi/Profile/MyNetwork/WlanXml</LocURI>
          </Target>
          <Meta>
            <Format xmlns="syncml:metinf">chr</Format>
          </Meta>
          <Data>&lt;?xml version=&quot;1.0&quot;?&gt;&lt;WLANProfile xmlns=&quot;https://www.microsoft.com/networking/WLAN/profile/v1&quot;&gt;&lt;name&gt;MyNetwork&lt;/name&gt;&lt;SSIDConfig&gt;&lt;SSID&gt;&lt;name&gt;MyNetwork&lt;/name&gt;&lt;/SSID&gt;&lt;/SSIDConfig&gt;&lt;connectionType&gt;ESS&lt;/connectionType&gt;&lt;connectionMode&gt;manual&lt;/connectionMode&gt;&lt;MSM&gt;&lt;security&gt;&lt;authEncryption&gt;&lt;authentication&gt;WPAPSK&lt;/authentication&gt;&lt;encryption&gt;TKIP&lt;/encryption&gt;&lt;/authEncryption&gt;&lt;sharedKey&gt;&lt;keyType&gt;passPhrase&lt;/keyType&gt;&lt;protected&gt;false&lt;/protected&gt;&lt;keyMaterial&gt;123456789&lt;/keyMaterial&gt;&lt;/sharedKey&gt;&lt;/security&gt;&lt;/MSM&gt;&lt;/WLANProfile&gt; </Data>
        </Item>
      </Add>
</Atomic>

The following example shows how to add PEAP-MSCHAPv2 network with SSID ‘MyNetwork’ and no proxy. The default is to prompt the user for server certificate validation).

<Atomic>
      <CmdID>300</CmdID>
      <Add>
        <CmdID>301</CmdID>
        <Item>
          <Target>
            <LocURI>./Vendor/MSFT/WiFi/Profile/MyNetwork/WlanXml</LocURI>
          </Target>
          <Meta>
            <Format xmlns="syncml:metinf">chr</Format>
          </Meta>
          <Data>&lt;?xml version=&quot;1.0&quot;?&gt;&lt;WLANProfile xmlns=&quot;https://www.microsoft.com/networking/WLAN/profile/v1&quot;&gt;&lt;name&gt;MyNetwork&lt;/name&gt;&lt;SSIDConfig&gt;&lt;SSID&gt;&lt;name&gt;MyNetwork&lt;/name&gt;&lt;/SSID&gt;&lt;nonBroadcast&gt;false&lt;/nonBroadcast&gt;&lt;/SSIDConfig&gt;&lt;connectionType&gt;ESS&lt;/connectionType&gt;&lt;connectionMode&gt;manual&lt;/connectionMode&gt;&lt;MSM&gt;&lt;security&gt;&lt;authEncryption&gt;&lt;authentication&gt;WPA2&lt;/authentication&gt;&lt;encryption&gt;AES&lt;/encryption&gt;&lt;useOneX&gt;true&lt;/useOneX&gt;&lt;/authEncryption&gt;&lt;OneX xmlns=&quot;https://www.microsoft.com/networking/OneX/v1&quot;&gt;&lt;authMode&gt;user&lt;/authMode&gt;&lt;EAPConfig&gt;&lt;EapHostConfig xmlns=&quot;https://www.microsoft.com/provisioning/EapHostConfig&quot;&gt;&lt;EapMethod&gt;&lt;Type xmlns=&quot;https://www.microsoft.com/provisioning/EapCommon&quot;&gt;25&lt;/Type&gt;&lt;VendorId xmlns=&quot;https://www.microsoft.com/provisioning/EapCommon&quot;&gt;0&lt;/VendorId&gt;&lt;VendorType xmlns=&quot;https://www.microsoft.com/provisioning/EapCommon&quot;&gt;0&lt;/VendorType&gt;&lt;AuthorId xmlns=&quot;https://www.microsoft.com/provisioning/EapCommon&quot;&gt;0&lt;/AuthorId&gt;&lt;/EapMethod&gt;&lt;Config xmlns=&quot;https://www.microsoft.com/provisioning/EapHostConfig&quot;&gt;&lt;Eap xmlns=&quot;https://www.microsoft.com/provisioning/BaseEapConnectionPropertiesV1&quot;&gt;&lt;Type&gt;25&lt;/Type&gt;&lt;EapType xmlns=&quot;https://www.microsoft.com/provisioning/MsPeapConnectionPropertiesV1&quot;&gt;&lt;ServerValidation&gt;&lt;DisableUserPromptForServerValidation&gt;false&lt;/DisableUserPromptForServerValidation&gt;&lt;ServerNames&gt;&lt;/ServerNames&gt;&lt;TrustedRootCA&gt;InsertCertThumbPrintHere&lt;/TrustedRootCA&gt;&lt;/ServerValidation&gt;&lt;FastReconnect&gt;true&lt;/FastReconnect&gt;&lt;InnerEapOptional&gt;false&lt;/InnerEapOptional&gt;&lt;Eap xmlns=&quot;https://www.microsoft.com/provisioning/BaseEapConnectionPropertiesV1&quot;&gt;&lt;Type&gt;26&lt;/Type&gt;&lt;EapType xmlns=&quot;https://www.microsoft.com/provisioning/MsChapV2ConnectionPropertiesV1&quot;&gt;&lt;UseWinLogonCredentials&gt;false&lt;/UseWinLogonCredentials&gt;&lt;/EapType&gt;&lt;/Eap&gt;&lt;EnableQuarantineChecks&gt;false&lt;/EnableQuarantineChecks&gt;&lt;RequireCryptoBinding&gt;false&lt;/RequireCryptoBinding&gt;&lt;PeapExtensions&gt;&lt;PerformServerValidation xmlns=&quot;https://www.microsoft.com/provisioning/MsPeapConnectionPropertiesV2&quot;&gt;true&lt;/PerformServerValidation&gt;&lt;AcceptServerName xmlns=&quot;https://www.microsoft.com/provisioning/MsPeapConnectionPropertiesV2&quot;&gt;false&lt;/AcceptServerName&gt;&lt;PeapExtensionsV2 xmlns=&quot;https://www.microsoft.com/provisioning/MsPeapConnectionPropertiesV2&quot;&gt;&lt;AllowPromptingWhenServerCANotFound xmlns=&quot;https://www.microsoft.com/provisioning/MsPeapConnectionPropertiesV3&quot;&gt;true&lt;/AllowPromptingWhenServerCANotFound&gt;&lt;/PeapExtensionsV2&gt;&lt;/PeapExtensions&gt;&lt;/EapType&gt;&lt;/Eap&gt;&lt;/Config&gt;&lt;/EapHostConfig&gt;&lt;/EAPConfig&gt;&lt;/OneX&gt;&lt;/security&gt;&lt;/MSM&gt;&lt;/WLANProfile&gt; </Data>
        </Item>
      </Add>
</Atomic>

Query network profiles

The following example shows how to query Wi-Fi profiles installed on an MDM server.

<Get> 
   <CmdID>301</CmdID> 
   <Item> 
      <Target> 
         <LocURI>./Vendor/MSFT/WiFi/Profile</LocURI> 
      </Target> 
   </Item> 
</Get>

The following example shows the response.

<Results> 
   <CmdID>3</CmdID> 
   <MsgRef>1</MsgRef> 
   <CmdRef>301</CmdRef>
   <Item> 
      <Source><LocURI>./Vendor/MSFT/WiFi/Profile</LocURI></Source> 
      <Meta><Format xmlns="syncml:metinf">node</Format></Meta> 
      <Data>TestWLAN1/TestWLAN2</Data> 
   </Item> 
</Results>

Remove a network

The following example shows how to remove a network with SSID ‘MyNetwork’ and no proxy. Removing all network authentication types is done in this same manner.

<Atomic>
      <CmdID>300</CmdID>
      <Delete>
        <CmdID>301</CmdID>
        <Item>
          <Target>
            <LocURI>./Vendor/MSFT/WiFi/Profile/MyNetwork/WlanXml</LocURI>
          </Target>
        </Item>
      </Delete>
</Atomic>

Add a network and a proxy

The following example shows how to add an open network with SSID ‘My Network’ and a proxy with url ‘test’ and port ‘80’. Adding a proxy to any network authentication type is done in this same manner.

<Atomic>
      <CmdID>300</CmdID>
      <Add>
        <CmdID>301</CmdID>
        <Item>
          <Target>
            <LocURI>./Vendor/MSFT/WiFi/Profile/MyNetwork/WlanXml</LocURI>
          </Target>
          <Meta>
            <Format xmlns="syncml:metinf">chr</Format>
          </Meta>
          <Data>&lt;?xml version=&quot;1.0&quot;?&gt;&lt;WLANProfile xmlns=&quot;https://www.microsoft.com/networking/WLAN/profile/v1&quot;&gt;&lt;name&gt;MyNetwork&lt;/name&gt;&lt;SSIDConfig&gt;&lt;SSID&gt;&lt;name&gt;MyNetwork&lt;/name&gt;&lt;/SSID&gt;&lt;/SSIDConfig&gt;&lt;connectionType&gt;ESS&lt;/connectionType&gt;&lt;connectionMode&gt;manual&lt;/connectionMode&gt;&lt;MSM&gt;&lt;security&gt;&lt;authEncryption&gt;&lt;authentication&gt;open&lt;/authentication&gt;&lt;encryption&gt;none&lt;/encryption&gt;&lt;/authEncryption&gt;&lt;/security&gt;&lt;/MSM&gt;&lt;/WLANProfile&gt; </Data>
        </Item>
      </Add>
      <Add>
        <CmdID>302</CmdID>
        <Item>
          <Target>
            <LocURI>./Vendor/MSFT/WiFi/Profile/MyNetwork/Proxy</LocURI>
          </Target>
          <Meta>
            <Format xmlns="syncml:metinf">chr</Format>
          </Meta>
          <Data>test:80</Data>
        </Item>
      </Add>
</Atomic>

Add a network and certification authority for a server certificate

The following example shows how to add PEAP-MSCHAPv2 network with SSID ‘MyNetwork’ and root CA validation for server certificate.

<Atomic>
      <CmdID>300</CmdID>
      <Add>
        <CmdID>301</CmdID>
        <Item>
          <Target>
            <LocURI>./Vendor/MSFT/WiFi/Profile/MyNetwork/WlanXml</LocURI>
          </Target>
          <Meta>
            <Format xmlns="syncml:metinf">chr</Format>
          </Meta>
          <Data>&lt;?xml version=&quot;1.0&quot;?&gt;&lt;WLANProfile xmlns=&quot;https://www.microsoft.com/networking/WLAN/profile/v1&quot;&gt;&lt;name&gt;MyNetwork&lt;/name&gt;&lt;SSIDConfig&gt;&lt;SSID&gt;&lt;name&gt;MyNetwork&lt;/name&gt;&lt;/SSID&gt;&lt;nonBroadcast&gt;false&lt;/nonBroadcast&gt;&lt;/SSIDConfig&gt;&lt;connectionType&gt;ESS&lt;/connectionType&gt;&lt;connectionMode&gt;manual&lt;/connectionMode&gt;&lt;MSM&gt;&lt;security&gt;&lt;authEncryption&gt;&lt;authentication&gt;WPA2&lt;/authentication&gt;&lt;encryption&gt;AES&lt;/encryption&gt;&lt;useOneX&gt;true&lt;/useOneX&gt;&lt;/authEncryption&gt;&lt;OneX xmlns=&quot;https://www.microsoft.com/networking/OneX/v1&quot;&gt;&lt;authMode&gt;user&lt;/authMode&gt;&lt;EAPConfig&gt;&lt;EapHostConfig xmlns=&quot;https://www.microsoft.com/provisioning/EapHostConfig&quot;&gt;&lt;EapMethod&gt;&lt;Type xmlns=&quot;https://www.microsoft.com/provisioning/EapCommon&quot;&gt;25&lt;/Type&gt;&lt;VendorId xmlns=&quot;https://www.microsoft.com/provisioning/EapCommon&quot;&gt;0&lt;/VendorId&gt;&lt;VendorType xmlns=&quot;https://www.microsoft.com/provisioning/EapCommon&quot;&gt;0&lt;/VendorType&gt;&lt;AuthorId xmlns=&quot;https://www.microsoft.com/provisioning/EapCommon&quot;&gt;0&lt;/AuthorId&gt;&lt;/EapMethod&gt;&lt;Config xmlns=&quot;https://www.microsoft.com/provisioning/EapHostConfig&quot;&gt;&lt;Eap xmlns=&quot;https://www.microsoft.com/provisioning/BaseEapConnectionPropertiesV1&quot;&gt;&lt;Type&gt;25&lt;/Type&gt;&lt;EapType xmlns=&quot;https://www.microsoft.com/provisioning/MsPeapConnectionPropertiesV1&quot;&gt;&lt;ServerValidation&gt;&lt;DisableUserPromptForServerValidation&gt;true&lt;/DisableUserPromptForServerValidation&gt;&lt;ServerNames&gt;&lt;/ServerNames&gt;&lt;TrustedRootCA&gt; InsertCertThumbPrintHere &lt;/TrustedRootCA&gt;&lt;/ServerValidation&gt;&lt;FastReconnect&gt;true&lt;/FastReconnect&gt;&lt;InnerEapOptional&gt;false&lt;/InnerEapOptional&gt;&lt;Eap xmlns=&quot;https://www.microsoft.com/provisioning/BaseEapConnectionPropertiesV1&quot;&gt;&lt;Type&gt;26&lt;/Type&gt;&lt;EapType xmlns=&quot;https://www.microsoft.com/provisioning/MsChapV2ConnectionPropertiesV1&quot;&gt;&lt;UseWinLogonCredentials&gt;false&lt;/UseWinLogonCredentials&gt;&lt;/EapType&gt;&lt;/Eap&gt;&lt;EnableQuarantineChecks&gt;false&lt;/EnableQuarantineChecks&gt;&lt;RequireCryptoBinding&gt;false&lt;/RequireCryptoBinding&gt;&lt;PeapExtensions&gt;&lt;PerformServerValidation xmlns=&quot;https://www.microsoft.com/provisioning/MsPeapConnectionPropertiesV2&quot;&gt;true&lt;/PerformServerValidation&gt;&lt;AcceptServerName xmlns=&quot;https://www.microsoft.com/provisioning/MsPeapConnectionPropertiesV2&quot;&gt;false&lt;/AcceptServerName&gt;&lt;/PeapExtensions&gt;&lt;/EapType&gt;&lt;/Eap&gt;&lt;/Config&gt;&lt;/EapHostConfig&gt;&lt;/EAPConfig&gt;&lt;/OneX&gt;&lt;/security&gt;&lt;/MSM&gt;&lt;/WLANProfile&gt; </Data>
        </Item>
      </Add>
</Atomic>

WiFi no prompt

<!--
Copyright (c) Microsoft Corporation.  All rights reserved.
-->
<SyncML xmlns="SYNCML:SYNCML1.2">
  <SyncBody>
    <Atomic>
      <CmdID>300</CmdID>
      <Add>
        <CmdID>301</CmdID>
        <Item>
          <Target>
            <LocURI>./Vendor/MSFT/WiFi/Profile/Testprofile/WlanXml</LocURI>
          </Target>
          <Meta>
            <Format xmlns="syncml:metinf">chr</Format>
          </Meta>
          <Data>&lt;?xml version=&quot;1.0&quot;?&gt;&lt;WLANProfile xmlns=&quot;https://www.microsoft.com/networking/WLAN/profile/v1&quot;&gt;&lt;name&gt;Testprofile&lt;/name&gt;&lt;SSIDConfig&gt;&lt;SSID&gt;&lt;hex&gt;412D4744414E&lt;/hex&gt;&lt;name&gt;Testprofile&lt;/name&gt;&lt;/SSID&gt;&lt;nonBroadcast&gt;false&lt;/nonBroadcast&gt;&lt;/SSIDConfig&gt;&lt;connectionType&gt;ESS&lt;/connectionType&gt;&lt;connectionMode&gt;manual&lt;/connectionMode&gt;&lt;MSM&gt;&lt;security&gt;&lt;authEncryption&gt;&lt;authentication&gt;WPA2&lt;/authentication&gt;&lt;encryption&gt;AES&lt;/encryption&gt;&lt;useOneX&gt;true&lt;/useOneX&gt;&lt;/authEncryption&gt;&lt;OneX xmlns=&quot;https://www.microsoft.com/networking/OneX/v1&quot;&gt;&lt;authMode&gt;user&lt;/authMode&gt;&lt;EAPConfig&gt;&lt;EapHostConfig xmlns=&quot;https://www.microsoft.com/provisioning/EapHostConfig&quot;&gt;&lt;EapMethod&gt;&lt;Type xmlns=&quot;https://www.microsoft.com/provisioning/EapCommon&quot;&gt;25&lt;/Type&gt;&lt;VendorId xmlns=&quot;https://www.microsoft.com/provisioning/EapCommon&quot;&gt;0&lt;/VendorId&gt;&lt;VendorType xmlns=&quot;https://www.microsoft.com/provisioning/EapCommon&quot;&gt;0&lt;/VendorType&gt;&lt;AuthorId xmlns=&quot;https://www.microsoft.com/provisioning/EapCommon&quot;&gt;0&lt;/AuthorId&gt;&lt;/EapMethod&gt;&lt;Config xmlns=&quot;https://www.microsoft.com/provisioning/EapHostConfig&quot;&gt;&lt;Eap xmlns=&quot;https://www.microsoft.com/provisioning/BaseEapConnectionPropertiesV1&quot;&gt;&lt;Type&gt;25&lt;/Type&gt;&lt;EapType xmlns=&quot;https://www.microsoft.com/provisioning/MsPeapConnectionPropertiesV1&quot;&gt;&lt;ServerValidation&gt;&lt;DisableUserPromptForServerValidation&gt;true&lt;/DisableUserPromptForServerValidation&gt;&lt;ServerNames&gt;&lt;/ServerNames&gt;&lt;/ServerValidation&gt;&lt;FastReconnect&gt;true&lt;/FastReconnect&gt;&lt;InnerEapOptional&gt;false&lt;/InnerEapOptional&gt;&lt;Eap xmlns=&quot;https://www.microsoft.com/provisioning/BaseEapConnectionPropertiesV1&quot;&gt;&lt;Type&gt;26&lt;/Type&gt;&lt;EapType xmlns=&quot;https://www.microsoft.com/provisioning/MsChapV2ConnectionPropertiesV1&quot;&gt;&lt;UseWinLogonCredentials&gt;false&lt;/UseWinLogonCredentials&gt;&lt;/EapType&gt;&lt;/Eap&gt;&lt;EnableQuarantineChecks&gt;false&lt;/EnableQuarantineChecks&gt;&lt;RequireCryptoBinding&gt;false&lt;/RequireCryptoBinding&gt;&lt;PeapExtensions&gt;&lt;PerformServerValidation xmlns=&quot;https://www.microsoft.com/provisioning/MsPeapConnectionPropertiesV2&quot;&gt;false&lt;/PerformServerValidation&gt;&lt;AcceptServerName xmlns=&quot;https://www.microsoft.com/provisioning/MsPeapConnectionPropertiesV2&quot;&gt;false&lt;/AcceptServerName&gt;&lt;/PeapExtensions&gt;&lt;/EapType&gt;&lt;/Eap&gt;&lt;/Config&gt;&lt;/EapHostConfig&gt;&lt;/EAPConfig&gt;&lt;/OneX&gt;&lt;/security&gt;&lt;/MSM&gt;&lt;/WLANProfile&gt; </Data>
        </Item>
      </Add>
      <Add>
        <CmdID>302</CmdID>
        <Item>
          <Target>
            <LocURI>./Vendor/MSFT/WiFi/Profile/Testprofile/Proxy</LocURI>
          </Target>
          <Meta>
            <Format xmlns="syncml:metinf">chr</Format>
          </Meta>
          <Data>proxy:80</Data>
        </Item>
      </Add>
    </Atomic>
    <Final/>
  </SyncBody>
</SyncML>