Event ID 1000 — RemoteApp and Desktop Connection Management Communication

Published: January 8, 2010

Applies To: Windows Server 2008 R2

yellow

RemoteApp and Desktop Connection Management communicates with the RD Session Host servers and RD Virtualization Host servers on your network to retrieve information about the RemoteApp programs, session-based desktops, and virtual desktops available on each server.

Event Details

Product: Windows Operating System
ID: 1000
Source: Microsoft-Windows-RemoteApp and Desktop Connection Management
Version: 6.1
Symbolic Name: TSCPUBSVR_WMI_ERROR
Message: Error in the WMI interface to %2. Check that the machine is running and connected to the network. If the problem persists, reboot the machine.

Error Code: %1

Resolve

Identify and fix network connectivity issues

To resolve this issue, identify and fix any network connectivity problems between the RD Session Host server and the RD Connection Broker server by doing the following:

  • Determine if there is a network connectivity problem by using the ping command.
  • Perform additional troubleshooting steps, if necessary, to help identify the cause of the problem.
  • Ensure that the Remote Desktop Session Host role service is installed.

To perform these tasks, refer to the following sections.

Note:  The following procedures include steps for using the ping command to perform troubleshooting. Therefore, before performing these steps, check whether the firewall or Internet Protocol security (IPsec) settings on your network allow Internet Control Message Protocol (ICMP) traffic. ICMP is the TCP/IP protocol that is used by the ping command.

To perform these procedures, you must have membership in the local Administrators group, or you must have been delegated the appropriate authority.

Determine if there is a network connectivity problem

To determine if there is a network connectivity problem between the RD Session Host server and the RD Connection Broker server:

  1. On the RD Session Host server, click Start, click Run, type cmd, and then click OK.
  2. At the command prompt, type ping server_FQDN, where server_FQDN is the fully qualified domain name (FQDN) of the RD Connection Broker server (for example, server1.contoso.com), and then press ENTER.

    If the ping was successful, you will receive a reply similar to the following:

    Reply from IP_address: bytes=32 time=3ms TTL=59

    Reply from IP_address: bytes=32 time=20ms TTL=59

    Reply from IP_address: bytes=32 time=3ms TTL=59

    Reply from IP_address: bytes=32 time=6ms TTL=59

  3. At the command prompt, type ping IP_address, where IP_address is the IP address of the RD Connection Broker server, and then press ENTER.

If you can successfully ping the domain controller by IP address, but not by FQDN, this indicates a possible issue with DNS host name resolution.

If you cannot successfully ping the RD Connection Broker server by IP address, this indicates a possible issue with network connectivity, firewall configuration, or IPsec configuration.

Perform additional troubleshooting steps

The following are some additional troubleshooting steps that you can perform to help identify the root cause of the problem:

  • Ping other computers on the network to help determine the extent of the network connectivity issue.
  • If you can ping other servers but not the RD Connection Broker server, try to ping the RD Connection Broker server from another computer. If you cannot ping the RD Connection Broker server from any computer, first ensure that the RD Connection Broker server is running. If the RD Connection Broker server is running, check the network settings on the RD Connection Broker server.
  • Check the TCP/IP settings on the local computer by doing the following:
    1. Click Start, click Run, type cmd, and then click OK.
    2. At the command prompt, type ipconfig /all, and then press ENTER. Make sure that the information listed is correct.
    3. Type ping localhost to verify that TCP/IP is installed and correctly configured on the local computer. If the ping is unsuccessful, this may indicate a corrupt TCP/IP stack or a problem with your network adapter.
    4. Type ping IP_address, where IP_address is the IP address assigned to the computer. If you can ping the localhost address but not the local address, there may be an issue with the routing table or with the network adapter driver.
    5. Type ping DNS_server, where DNS_server is the IP address assigned to the DNS server. If there is more than one DNS server on your network, you should ping each one. If you cannot ping the DNS servers, this indicates a potential problem with the DNS servers, or with the network between the computer and the DNS servers.
    6. If the RD Connection Broker server is on a different subnet, try to ping the default gateway. If you cannot ping the default gateway, this might indicate a problem with the network adapter, the router or gateway device, cabling, or other connectivity hardware.
  • In Device Manager, check the status of the network adapter. To open Device Manager, click Start, click Run, type devmgmt.msc, and then click OK.
  • Check network connectivity indicator lights on the computer and at the hub or router. Check network cabling.
  • Check firewall settings by using the Windows Firewall with Advanced Security snap-in.
  • Check IPsec settings by using the IP Security Policy Management snap-in.

Ensure that the Remote Desktop Session Host role service is installed

The Remote Desktop Session Host role service must be installed on the server that is indicated in the event message text.

To ensure that the Remote Desktop Session Host role service is installed:

  1. Open Server Manager. To open Server Manager, click Start, point to Administrative Tools, and then click Server Manager.
  2. Expand Roles, and then click Remote Desktop Services.
  3. Under Role Services, locate Remote Desktop Session Host.
  4. Ensure that Installed displays in the Status column.

Verify

To verify that RemoteApp and Desktop Connection Management can communicate with the RD Session Host servers and the RD Virtualization Host servers, do the following:

  • Verify that the RemoteApp and Desktop Connection Management service is started.
  • Log on to the RD Web Access server that is configured to use the RD Connection Broker server.

Verify that the RemoteApp and Desktop Connection Management service is started

The RemoteApp and Desktop Connection Management service is used to communicate with the RD Session Host and RD Virtualization Host servers on your network.

To verify that the RemoteApp and Desktop Connection Management service is started:

  1. On the RD Connection Broker server, open the Services console. To open the Services console, click Start, point to Administrative Tools, and then click Services.
  2. Locate the service named RemoteApp and Desktop Connection Management.
  3. Verify that the Status column for this service displays Started.
  4. After you have verified that the RemoteApp and Desktop Connection Management service is started, log on to the RD Web Access server as outlined in the section "Log on to the RD Web Access server that is configured to use the RD Connection Broker server."

Log on to the RD Web Access server that is configured to use the RD Connection Broker server

The RD Web Access server that is configured to use the RD Connection Broker server must be available to communicate with the RD Connection Broker server.

To log on to the RD Web Access server that is configured to use the RD Connection Broker server:

  1. On the RD Web Access server, open Remote Desktop Web Access Configuration. To open Remote Desktop Web Access Configuration, click Start, point to Administrative Tools, point to Remote Desktop Services, and then click Remote Desktop Web Access Configuration.
  2. In the Domain\user name box, type a valid domain and user account name.
  3. In the Password box, type the password for the user account.
  4. Verify that you can successfully log on to the RD Web Access server by using Remote Desktop Web Access Configuration.

Related Management Information

RemoteApp and Desktop Connection Management Communication

Remote Desktop Services

Community Additions

ADD
Show: