TechNet
Export (0) Print
Expand All
Collapse the table of content
Expand the table of content
Expand Minimize

Set-DlpPolicy

 

Applies to: Exchange Online, Exchange Server 2016

This cmdlet is available in on-premises Exchange Server 2016 and in the cloud-based service. Some parameters and settings may be exclusive to one environment or the other.

Use the Set-DlpPolicy cmdlet to modify data loss prevention (DLP) policies in your organization.

For information about the parameter sets in the Syntax section below, see Syntax.

Set-DlpPolicy -Identity <DlpPolicyIdParameter> [-Confirm [<SwitchParameter>]] [-Description <String>] [-DomainController <Fqdn>] [-Mode <Audit | AuditAndNotify | Enforce>] [-Name <String>] [-State <Enabled | Disabled>] [-WhatIf [<SwitchParameter>]]

This example disables the DLP policy named Employee Numbers.

Set-DlpPolicy "Employee Numbers" -State Disabled

You need to be assigned permissions before you can run this cmdlet. Although all parameters for this cmdlet are listed in this topic, you may not have access to some parameters if they're not included in the permissions assigned to you. To see what permissions you need, see the "Data loss prevention (DLP)" entry in the Messaging policy and compliance permissions topic.

 

Parameter Required Type Description

Identity

Required

Microsoft.Exchange.MessagingPolicies.CompliancePrograms.Tasks.DlpPolicyIdParameter

The Identity parameter specifies the DLP policy you want to modify. You can use any value that uniquely identifies the DLP policy. For example, you can specify the name, GUID, or distinguished name (DN) of the DLP policy.

Confirm

Optional

System.Management.Automation.SwitchParameter

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

  • Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.

  • Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.

Description

Optional

System.String

The Description parameter specifies an optional description for the DLP policy.

DomainController

Optional

Microsoft.Exchange.Data.Fqdn

This parameter is available only in on-premises Exchange 2016.

The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.

Mode

Optional

Microsoft.Exchange.MessagingPolicies.Rules.RuleMode

The Mode parameter specifies the action and notification level of the DLP policy. Valid values for this parameter are:

  • Audit: When a message matches the conditions specified by the DLP policy, the actions specified by the policy aren't enforced, and no notification emails are sent.

  • AuditAndNotify: When a message matches the conditions specified by the DLP policy, the actions specified by the policy aren't enforced, but notification emails are sent.

  • Enforce: When a message matches the conditions specified by the DLP policy, the actions specified by the policy are enforced, and notification emails are sent.

If the State parameter is set to Disabled, the value of the Mode parameter is irrelevant.

Name

Optional

System.String

The Name parameter specifies a unique name for the DLP policy.

State

Optional

Microsoft.Exchange.MessagingPolicies.Rules.RuleState

The State parameter enables or disables the DLP policy. Valid input for this parameter is Enabled or Disabled.

WhatIf

Optional

System.Management.Automation.SwitchParameter

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn’t accept input data.

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn’t return data.

 
Show:
© 2016 Microsoft