Applies to: Exchange Server 2013

This cmdlet is available only in on-premises Exchange Server 2013.

Use the Add-ServerMonitoringOverride cmdlet to override the thresholds and parameters of managed availability probes, monitors, and responders on specific Exchange 2013 servers.

For information about the parameter sets in the Syntax section below, see Syntax.

Add-ServerMonitoringOverride [-Duration <EnhancedTimeSpan>] <COMMON PARAMETERS>
Add-ServerMonitoringOverride -ApplyVersion <Version> <COMMON PARAMETERS>
COMMON PARAMETERS: -Identity <String> -ItemType <Probe | Monitor | Responder | Maintenance> -PropertyName <String> -PropertyValue <String> -Server <ServerIdParameter> [-Confirm [<SwitchParameter>]] [-WhatIf [<SwitchParameter>]]

This example adds a server monitoring override that disables the responder ActiveDirectoryConnectivityConfigDCServerReboot on the server named EXCH03 for 20 days. Note that the value of Identity is case-sensitive.

Add-ServerMonitoringOverride -Identity "AD\ActiveDirectoryConnectivityConfigDCServerReboot" -Server EXCH03 -ItemType Responder -PropertyName Enabled -PropertyValue 0 -Duration 20.00:00:00

You need to be assigned permissions before you can run this cmdlet. Although all parameters for this cmdlet are listed in this topic, you may not have access to some parameters if they're not included in the permissions assigned to you. To see what permissions you need, see the "Shell infrastructure permissions" section in the Exchange and Shell infrastructure permissions topic.


Parameter Required Type Description




The ApplyVersion parameter specifies the version of Exchange that gets the override. f you update Exchange to a newer version (for example, you apply a Cumulative Update or Service Pack), the override is no longer applied to the server.

Valid input for this parameter is an Exchange version number in the format

You can't use this parameter with the Duration parameter.




The Identity parameter specifies the identity of the monitoring item that you want to override. This parameter uses the syntax <HealthSet>\<MonitoringItemName>[\<TargetResource>]. Note that the values are case sensitive. For example, use "AD\ActiveDirectoryConnectivityConfigDCServerReboot", not "ad\activedirectoryconnectivityconfigdcserverreboot".

You can use Get-ServerHealth to find the correct object for the monitoring item you want to override.




The ItemType parameter specifies the server item type for the property that you want to override. Valid value are:

  • Probe

  • Monitor

  • Responder




The PropertyName parameter specifies the server property that you want to override.




The PropertyValue parameter specifies the new value for the server property that you want to override.




The Server parameter specifies the Exchange server where you want to add the monitoring override. You can use any value that uniquely identifies the server. For example:

  • Name

  • FQDN

  • Distinguished name (DN)

  • Exchange Legacy DN

You can't use this parameter to configure other Edge Transport servers remotely.




The Confirm switch causes the command to pause processing and requires you to acknowledge what the command will do before processing continues. You don't have to specify a value with the Confirm switch.




The Duration parameter specifies the length of time that the override is active.

To specify a value, enter it as a time span: dd.hh:mm:ss where d = days, h = hours, m = minutes, and s = seconds.

For example, 30.10:00:00 specifies 30 days and 10 hours.

You can't use this parameter with the ApplyVersion parameter.




The WhatIf switch instructs the command to simulate the actions that it would take on the object. By using the WhatIf switch, you can view what changes would occur without having to apply any of those changes. You don't have to specify a value with the WhatIf switch.

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn’t accept input data.

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn’t return data.