Get-DAServer

Get-DAServer

Displays the properties of the DirectAccess (DA) server.

Sintaxis

Parameter Set: Get0
Get-DAServer [[-EntrypointName] <String> ] [-AsJob] [-CimSession <CimSession[]> ] [-ComputerName <String> ] [-ThrottleLimit <Int32> ] [ <CommonParameters>]

Descripción detallada

The Get-DAServer cmdlet displays the properties of the DirectAccess (DA) server.

The output displayed consists of the following.

Global Configuration: These properties are applicable to the entire DA deployment.
-- DA installation configuration: full install or only manage-out.
-- Internal IPv6 prefix.
-- Authentication type.
-- IPsec root certificate: The certificate is always configured separately on every server, although the same certificate issued by same root is present on all DA servers.
-- Intermediate root certificate usage: enabled or disabled.
-- Computer certificate authentication: enabled or disabled.
-- DA server GPO name.
-- Health check: enabled or disabled.

For the following properties either the server-level or cluster level, if load balancing has been deployed, configuration is returned. If multi-site is deployed, then this configuration is applicable at the site-level and configuration for the specified site is displayed.
-- Client IPv6 prefix.
-- Teredo State.
-- Whether NAT is enabled.
-- Does DA server have a single network adapter or two network adapters.

The following are pure server-level properties that are returned. In a multi-site deployment if both the EntryPointName and ComputerName parameters are specified, but the ComputerName parameter value does not belong to that entry point name, then no values are returned for these properties. However, if only the EntryPointName parameter is specified or the ComputerName parameter value is also specified and belongs to the specified entry point name, then the configuration is retrieved from the server on which the cmdlet is run as follows.
-- Internet interface.
-- Internal interface.
-- SSL certificate.

Parámetros

-AsJob

-CimSession<CimSession[]>

Ejecuta el cmdlet en una sesión remota o en un equipo remoto. Escriba un nombre de equipo o un objeto de sesión, como la salida de un cmdlet New-CimSession o Get-CimSession. El valor predeterminado es la sesión actual en el equipo local.

-ComputerName<String>

Specifies the IPv4 or IPv6 address, or host name, of the computer on which the DA server computer specific tasks should be run.

-EntrypointName<String>

Specifies the identity of a site in a multi-site deployment and when specified indicates that the configuration of the DA server at that site should be retrieved.
If this parameter is not specified in a multi-site deployment then the entry point to which the server on which this cmdlet is run is used. The server could also be represented by using the ComputerName parameter.
If both this parameter and ComputerName parameter are specified and the computer name does not belong to the site represented by this parameter then this parameter takes precedence and the configuration is returned for it.

-ThrottleLimit<Int32>

Especifica el número máximo de operaciones simultáneas que se pueden establecer para ejecutar el cmdlet. Si se omite este parámetro o es especifica un valor de 0, Windows PowerShell ® calcula un límite óptimo para el cmdlet en función del número de cmdlets de CIM que se estén ejecutando en el equipo. El límite solo se aplica al cmdlet actual, no a la sesión ni al equipo.

<CommonParameters>

Este cmdlet admite los siguientes parámetros comunes: -Verbose, -Debug, -ErrorAction, -ErrorVariable, -OutBuffer y -OutVariable. Para obtener más información, consulte about_CommonParameters (https://go.microsoft.com/fwlink/p/?LinkID=113216).

Entradas

El tipo de entrada es el tipo de los objetos que se pueden canalizar al cmdlet.

• None

Salidas

El tipo de resultado es el tipo de objetos que emite el cmdlet.

• Microsoft.Management.Infrastructure.CimInstance#MSFT_DAServer

  El objeto Microsoft.Management.Infrastructure.CimInstance es una clase contenedora que muestra objetos de Instrumental de administración de Windows (WMI). La ruta de acceso después del signo de número (#) proporciona el espacio de nombres y el nombre de clase del objeto WMI subyacente.
  The output object contains the following properties:
  -- Type of DA installation: full or managed.
  -- Authentication type.
  -- Internal IPv6 prefix.
  -- Client IPHTTPS IPv6 prefix.
  -- Usage of computer certificate authorization for 1st tunnel: Enabled or Disabled.
  -- IPsec root certificate.
  -- Whether the IPsec root certificate is an intermediate root certificate.
  -- Status of Teredo: Enabled or Disabled.
  -- Whether the DA server is deployed behind NAT.
  -- Whether the configuration in which DA is deployed is a single or double network adapter.
  -- Name of the DA server GPO.
  -- Status of the health check.

Ejemplos

EXAMPLE 1

This example displays the properties of the local DA server.

PS C:\> Get-DAServer

Temas relacionados

Get-DAServer

Get-RemoteAccess