Set-DhcpServerv6Scope

Set-DhcpServerv6Scope

Modifies the properties of the IPv6 scope on the Dynamic Host Configuration Protocol (DHCP) server service.

Syntax

Parameter Set: Set3
Set-DhcpServerv6Scope [-Prefix] <IPAddress> [-AsJob] [-CimSession <CimSession[]> ] [-ComputerName <String> ] [-Description <String> ] [-Name <String> ] [-PassThru] [-Preference <UInt16> ] [-PreferredLifeTime <TimeSpan> ] [-State <String> ] [-T1 <TimeSpan> ] [-T2 <TimeSpan> ] [-ThrottleLimit <Int32> ] [-ValidLifeTime <TimeSpan> ] [-Confirm] [-WhatIf] [ <CommonParameters>]

Detailed Description

The Set-DhcpServerv6Scope cmdlet modifies the properties of the IPv6 scope on the Dynamic Host Configuration Protocol (DHCP) server service.

Parameters

-AsJob

-CimSession<CimSession[]>

Runs the cmdlet in a remote session or on a remote computer. Enter a computer name or a session object, such as the output of a New-CimSession or Get-CimSession cmdlet. The default is the current session on the local computer.

-ComputerName<String>

Specifies the DNS name, or IPv4 or IPv6 address, of the target computer running the DHCP server service.

-Description<String>

Specifies the description to set on the scope.

-Name<String>

Specifies the new name to set for the scope.

-PassThru

Returns an object representing the item with which you are working. By default, this cmdlet does not generate any output.

-Preference<UInt16>

Specifies the preference value of the DHCP server service. The DHCP server service with the lowest preference value is selected by the DHCP client in case the client gets responses from more than one DHCP server service.

-PreferredLifeTime<TimeSpan>

Specifies the preferred life time of the IPv6 address leased by the DHCP server service.
This parameter value should be same or less than the ValidLifeTime parameter value.

-Prefix<IPAddress>

Specifies the IPv6 subnet prefix of the scope for which the properties are modified.

-State<String>

Specifies the state of the scope. The acceptable values for this parameter are: Active or Inactive.

-T1<TimeSpan>

Specifies the lease renewal time. The DHCP client is expected to use a unicast message to renew the lease at the time specifies by this parameter value from the same DHCP server service from which DHCP client had initially obtained the lease. This parameter value should be less than the T2 and PreferredLifetime parameter values for the scope.

-T2<TimeSpan>

Specifies the lease rebind time. The client is expected to use a multi-cast message to renew the lease at the time equal to this parameter value from any DHCP server service if the renewal attempt at time specified by the T1 parameter fails.
This parameter value should be greater than the T1 parameter value and less than the PreferredLifetime parameter value.

-ThrottleLimit<Int32>

Specifies the maximum number of concurrent operations that can be established to run the cmdlet. If this parameter is omitted or a value of 0 is entered, then Windows PowerShell® calculates an optimum throttle limit for the cmdlet based on the number of CIM cmdlets that are running on the computer. The throttle limit applies only to the current cmdlet, not to the session or to the computer.

-ValidLifeTime<TimeSpan>

Specifies the valid life time of the IPv6 address leased by the DHCP server service.
This parameter value should be same or greater than the PreferredLifetime parameter value.

-Confirm

Prompts you for confirmation before running the cmdlet.

-WhatIf

Shows what would happen if the cmdlet runs. The cmdlet is not run.

<CommonParameters>

This cmdlet supports the common parameters: -Verbose, -Debug, -ErrorAction, -ErrorVariable, -OutBuffer, and -OutVariable. For more information, see    about_CommonParameters (https://go.microsoft.com/fwlink/p/?LinkID=113216).

Inputs

The input type is the type of the objects that you can pipe to the cmdlet.

• Microsoft.Management.Infrastructure.CimInstance#root/Microsoft/Windows/DHCP/DhcpServerv6Scope

  The Microsoft.Management.Infrastructure.CimInstance object is a wrapper class that displays Windows Management Instrumentation (WMI) objects. The path after the pound sign (#) provides the namespace and class name for the underlying WMI object.

Outputs

The output type is the type of the objects that the cmdlet emits.

• Microsoft.Management.Infrastructure.CimInstance#root/Microsoft/Windows/DHCP/DhcpServerv6Scope

  The Microsoft.Management.Infrastructure.CimInstance object is a wrapper class that displays Windows Management Instrumentation (WMI) objects. The path after the pound sign (#) provides the namespace and class name for the underlying WMI object.

Examples

EXAMPLE 1

This example changes the name of the specified DHCPv6 scope to Ext Lab Net VLAN100 and activates the scope.

PS C:\> Set-DhcpServerv6Scope -ComputerName dhcpserver.contoso.com -Prefix 2001:4898:7020:1020:: -Name "Ext Lab Net VLAN100" -State Active

Related topics

Add-DhcpServerv6Scope

Get-DhcpServerv6Scope

Get-DhcpServerv6ScopeStatistics

Remove-DhcpServerv6Scope