New-Cluster

New-Cluster

Creates a new failover cluster.

構文

Parameter Set: Default
New-Cluster [-Name] <String> [-AdministrativeAccessPoint <AdminAccessPoint> {ActiveDirectoryAndDns | Dns | None} ] [-Force] [-IgnoreNetwork <StringCollection> ] [-Node <StringCollection> ] [-NoStorage] [-StaticAddress <StringCollection> ] [ <CommonParameters>]

詳細説明

The New-Cluster cmdlet creates a new failover cluster. Before creating a cluster, the hardware (servers, networks, and storage) must be connected, and the validation tests must be run.

Use Test-Cluster to run the validation tests. The tests will confirm that the hardware and settings are compatible with failover clustering. There are multiple types of tests, including Inventory, System Configuration, Network, Storage, and other types of tests.

Note:このコマンドレットは、サーバー コンピューターに Credential Security Service Provider (CredSSP) 認証がない場合、リモートで実行できません。

パラメーター

-AdministrativeAccessPoint<AdminAccessPoint>

Specifies the type of administrative access point that the cmdlet creates for the cluster. このパラメーターに対して使用できる値:

-- ActiveDirectoryAndDns. The cmdlet creates an administrative access point for the cluster. The administrative access point is registered in DNS and enabled in Active Directory ドメイン サービス.
-- Dns. The cmdlet creates an administrative access point for the cluster. The administrative access point is registered in DNS but is not enabled in Active Directory ドメイン サービス.
-- None. The cmdlet does not create an administrative access point for the cluster. Some clustered roles and functionality might not be available for a cluster that does not have an administrative access point. Also, you cannot use Failover Cluster Manager to manage a cluster that does not have an administrative access point.

-Force

ユーザーの確認を求めずにコマンドを強制的に実行します。

-IgnoreNetwork<StringCollection>

Specifies one or more networks to ignore when running the cmdlet. Networks with DHCP enabled are always included, but other networks need a static address to be specified using the StaticAddress parameter or should be explicitly ignored with this IgnoreNetwork parameter.

-Name<String>

Specifies the name of the cluster to create.

-NoStorage

Specifies that shared storage is ignored during the cluster creation. The cluster created at the end of the operation will not have shared storage. Shared storage can later be added by piping the ClusterDiskInfo object from the Get-ClusterAvailableDisk cmdlet into the Add-ClusterDisk cmdlet.

-Node<StringCollection>

Specifies a comma-separated list of cluster node names, or server names, on which to create the cluster. If this parameter is not specified, then a one node cluster is created on the local physical computer.

-StaticAddress<StringCollection>

Specifies one or more static addresses to use when running the cmdlet. Networks with DHCP enabled are always included, but other networks need a static address to be specified using the StaticAddress parameter or should be explicitly ignored with this IgnoreNetwork parameter.

<CommonParameters>

このコマンドレットは次の共通パラメーターをサポートします。-Verbose、-Debug、-ErrorAction、-ErrorVariable、-OutBuffer、-OutVariable.詳細については、以下を参照してください。 about_CommonParameters (https://go.microsoft.com/fwlink/p/?LinkID=113216)。

入力

入力型は、コマンドレットにパイプできるオブジェクトの型です。

• None

出力

出力型は、コマンドレットによって生成されるオブジェクトの型です。

• Microsoft.FailoverClusters.PowerShell.Cluster

例

EXAMPLE 1

This example creates a four-node cluster named cluster1, using default settings for IP addressing.

PS C:\> New-Cluster -Name cluster1 -Node node1,node2,node3,node4

EXAMPLE 2

This example creates a two-node cluster named cluster1. The cluster will not have any clustered storage, or disk resources. Storage can be added using the Get-ClusterAvailableDisk cmdlet with the Add-ClusterDisk cmdlet.

PS C:\> New-Cluster -Name cluster1 -Node node1,node2 -NoStorage

EXAMPLE 3

This example creates a four-node cluster named cluster1 that uses the static IP address 2.0.0.123.

PS C:\> New-Cluster -Name cluster1 -Node node1,node2,node3,node4 -StaticAddress 2.0.0.123

EXAMPLE 4

This example creates a four-node cluster named cluster1 that uses the static IP addresses 2.0.0.123 and 3.0.0.123.

PS C:\> New-Cluster -Name cluster1 -Node node1,node2,node3,node4 -StaticAddress 2.0.0.123,3.0.0.123

EXAMPLE 5

This example creates a four-node cluster named cluster1. The cluster uses default settings for IP addressing, and does not use the network 2.0.0.0/8.

PS C:\> New-Cluster -Name cluster1 -Node node1,node2,node3,node4 -IgnoreNetwork 2.0.0.0/8

EXAMPLE 6

This example creates a four-node cluster named cluster1. The cluster uses the static IP address 2.0.0.123, and does not use the network 3.0.0.0/8.

PS C:\> New-Cluster -Name cluster1 -Node node1,node2,node3,node4 -StaticAddress 2.0.0.123 -IgnoreNetwork 3.0.0.0/8

関連トピック

Add-ClusterNode

Get-Cluster

Remove-Cluster

Start-Cluster

Stop-Cluster

Test-Cluster