New-NetLbfoTeam

New-NetLbfoTeam

Creates a new NIC team.

構文

Parameter Set: cim:CreateInstance0
New-NetLbfoTeam [-Name] <String> [-TeamMembers] <WildcardPattern[]> [[-TeamNicName] <String> ] [[-TeamingMode] <TeamingModes> ] [[-LoadBalancingAlgorithm] <LBAlgos> ] [-AsJob] [-CimSession <CimSession[]> ] [-ThrottleLimit <Int32> ] [-Confirm] [-WhatIf] [ <CommonParameters>]

詳細説明

The New-NetLbfoTeam cmdlet creates a new NIC team that consists of one or more network adapters. Teaming network adapters of different speeds is not supported. You can create a team with network adapters of different speeds, but the network traffic distribution algorithms do not take the speed of each network adapter into consideration when distributing traffic.

When you create a team, you can specify additional properties such as TeamingMode and LoadBalancingAlgorithm.

You need administrator privileges to use New-NetLbfoTeam.

パラメーター

-AsJob

-CimSession<CimSession[]>

リモート セッションまたはリモート コンピューターでコマンドレットを実行します。New-CimSession コマンドレットや Get-CimSession コマンドレットの出力など、コンピューター名またはセッション オブジェクトを入力します。既定値は、ローカル コンピューターで実行中の現在のセッションです。

-LoadBalancingAlgorithm<LBAlgos>

Specifies the load-balancing algorithm the new team uses to distribute network traffic between the interfaces.

You can specify one of the following five load balancing algorithms:

Dynamic:  Uses the source and destination TCP ports and the IP addresses to create a hash for outbound traffic.  Moves outbound streams from team member to team member as needed to balance team member utilization.  When you specify this algorithm with the TeamingMode parameter and the SwitchIndependent value, inbound traffic is routed to a particular team member. 

TransportPorts: Uses the source and destination TCP ports and the IP addresses to create a hash and then assigns the packets that have the matching hash value to one of the available interfaces. When you specify this algorithm with the TeamingMode parameter and the SwitchIndependent value all inbound traffic arrives on the primary team member.

IPAddresses: Uses the source and destination IP addresses to create a hash and then assigns the packets that have the matching hash value to one of the available interfaces. When you specify this algorithm with the TeamingMode parameter and the SwitchIndependent value, all inbound traffic arrives on the primary team member.

MacAddresses: Uses the source and destination MAC addresses to create a hash and then assigns the packets that have the matching hash value to one of the available interfaces. When you specify this algorithm with the TeamingMode parameter and the SwitchIndependent value, all inbound traffic arrives on the primary team member.

HyperVPort: Distributes network traffic based on the source virtual machine Hyper-V switch port identifier. When you specify this algorithm with the TeamingMode parameter and the SwitchIndependent value, inbound traffic is routed to the same team member as the switch port’s outgoing traffic.

-Name<String>

Specifies the name of the new NIC team.

-TeamMembers<WildcardPattern[]>

Specifies the names of the network adapters that are members of the new team. Specify multiple network adapter names (or wildcard patterns) separated by a comma.

-TeamNicName<String>

Specifies the name of the new team interface. This is the name used to reference the teamed network adapters.

-TeamingMode<TeamingModes>

Specifies the mode of the NIC teaming. You can specify one of the following three teaming modes:

LACP: Uses the IEEE 802.1ax Link Aggregation Control Protocol (LACP) to dynamically identify links that are connected between the host and a given switch. (This protocol was formerly known as IEEE 802.3ad draft)

Static: Requires configuration on both the switch and the host to identify which links form the team.

SwitchIndependent: Specifies that a network switch configuration is not needed for the NIC team. Because the network switch is not configured to know about the interface teaming, the team interfaces can be connected to different switches.

-ThrottleLimit<Int32>

このコマンドレットを実行するために確立できる最大同時操作数を指定します。このパラメーターを省略するか、値として 0 を入力した場合、Windows PowerShell® では、コンピューターで実行している CIM コマンドレットの数に基づいて、コマンドレットに対する最適なスロットル制限を計算します。スロットル制限は現在のコマンドレットのみに適用され、セッションまたはコンピューターには適用されません。

-Confirm

コマンドレットを実行する前に、ユーザーに確認を求めます。

-WhatIf

コマンドレットを実行するとどのような結果になるかを表示します。コマンドレットは実行されません。

<CommonParameters>

このコマンドレットは次の共通パラメーターをサポートします。-Verbose、-Debug、-ErrorAction、-ErrorVariable、-OutBuffer、-OutVariable.詳細については、以下を参照してください。 about_CommonParameters (https://go.microsoft.com/fwlink/p/?LinkID=113216)。

入力

入力型は、コマンドレットにパイプできるオブジェクトの型です。

• None

  This cmdlet takes no input objects.

出力

出力型は、コマンドレットによって生成されるオブジェクトの型です。

• MSFT_NetLbfoTeam

  This cmdlet produces an MSFT_NetLbfoTeam object, corresponding to the newly created team.

例

---------- Example 1: Create a new team ----------

This command creates a new team named Team1 with two team members named NIC1 and NIC2.

PS C:\> New-NetLbfoTeam –Name Team1 –TeamMembers NIC1,NIC2

---------- Example 2: Create a new team with specified properties ----------

This command creates a new team named Team1 that consists of two team members named NIC1 and NIC2. The teaming mode is set to LACP and the load balancing algorithm is set to HyperVPorts.

PS C:\> New-NetLbfoTeam -Name Team1 -TeamMembers NIC1,NIC2 -TeamingMode LACP -LoadBalancingAlgorithm HyperVPorts

---------- Example 3: Create a new team in a virtual machine ----------

This set of commands allows teaming in virtual machines by using the AllowTeaming parameter of the Set-VMNetworkAdapter cmdlet and then creates a team named Team2 in the virtual machine specified by VMName. You must run the following command in the host (parent partition) with administrator permissions.

PS C:\> Set-VMNetworkAdapter -VMName <VMname> -AllowTeaming On
PS C:\> New-NetLbfoTeam –Name Team2 –TeamMembers NIC1,NIC2

関連トピック

Get-NetLbfoTeam

Set-NetLbfoTeam

Rename-NetLbfoTeam

Remove-NetLbfoTeam