Start-PcsvDevice

업데이트 날짜: 2015년 2월

적용 대상: Windows 10 Technical Preview, Windows Server Technical Preview

Start-PcsvDevice

Starts the specified remote hardware device.

구문

Parameter Set: InputObject (cdxml)
Start-PcsvDevice [-CimSession <CimSession[]> ] [-PassThru] [-ThrottleLimit <Int32> ] [-Confirm] [-WhatIf] [ <CommonParameters>]

Parameter Set: ByComputerName
Start-PcsvDevice [-TargetAddress] <String> [-Credential] <PSCredential> [-ManagementProtocol] <ManagementProtocol> {WSMan | IPMI} [[-Port] <UInt16> ] [-Authentication <Authentication> {Default | Basic | Digest} ] [-CimSession <CimSession[]> ] [-PassThru] [-SkipCACheck] [-SkipCNCheck] [-SkipRevocationCheck] [-ThrottleLimit <Int32> ] [-TimeoutSec <UInt32> ] [-UseSSL] [-Confirm] [-WhatIf] [ <CommonParameters>]

자세한 설명

The Start-PcsvDevice cmdlet starts a remote hardware device by using Web Services for Management (WS-Management) or Intelligent Platform Management Interface (IPMI). The cmdlet puts the device in the Enabled state, which corresponds to a startup of the hardware device. Specify the remote hardware device by the management name or IP address, provide credentials necessary to start the remote hardware device, and specify which management protocol to use. The credentials must have administrator permissions on the remote hardware device. You can also specify an authentication type to use for WS-Management.

매개 변수

-Authentication<Authentication>

Specifies an authentication method to use for devices managed by using WS-Management. Do not specify this parameter for devices managed by using IPMI. 이 매개 변수에 허용되는 값은 다음과 같습니다.

-- Basic
-- Digest
-- Default

If you specify Default for this parameter and a value of WSMAN for the ManagementProtocol parameter, the cmdlet uses Basic authentication.

-CimSession<CimSession[]>

원격 세션이나 원격 컴퓨터에서 cmdlet을 실행합니다. 컴퓨터 이름이나 New-CimSession 또는 Get-CimSession cmdlet의 출력과 같은 세션 개체를 입력하세요. 기본값은 로컬 컴퓨터 상의 현재 세션입니다.

-Credential<PSCredential>

Specifies a PSCredential object based on a user name and password. To obtain a PSCredential object, use the Get-Credential cmdlet. For more information, type Get-Help Get-Credential. This parameter specifies the credential for the remote hardware device.

-ManagementProtocol<ManagementProtocol>

Specifies a management protocol used to communicate with a device. 이 매개 변수에 허용되는 값은 다음과 같습니다.

-- WSMAN
-- IPMI

Refer to your hardware documentation for supported management protocols.

Specify WSMAN for devices that represent information by using Systems Management Architecture for Server Hardware (SMASH), Desktop and mobile Architecture for System Hardware (DASH) or Physical Computer System View profiles.

-PassThru

작업 중인 항목을 나타내는 개체를 반환합니다. 기본적으로 이 cmdlet은 출력을 생성하지 않습니다.

-Port<UInt16>

Specifies a port on the remote computer to use for the management connection. If you do not specify a port, the cmdlet uses the following default values:

-- IPMI and WSMAN over HTTP. Port 623.
-- WSMAN over HTTPS. Port 664.

-SkipCACheck

Indicates that the client connects by using HTTPS without validating that a trusted CA signed the server certificate. Do not specify this parameter if you specify a value of IPMI for the ManagmentProtocol parameter.

Do not specify this parameter unless you can establish trust in another way, such as if the remote computer is part of a network that is physically secure and isolated, or if the remote computer is a trusted host in a Windows Remote Management (WinRM) configuration.

-SkipCNCheck

Indicates that the certificate common name of the server does not need to match the host name of the server. Do not specify this parameter if you specify a value of IPMI for the ManagmentProtocol parameter.

Specify this parameter only for managing devices by using WS-Management over HTTPS. Be sure to specify this parameter only for trusted computers.

-SkipRevocationCheck

Indicates that the cmdlet skips the revocation check of server certificates. Do not specify this parameter if you specify a value of IPMI for the ManagmentProtocol parameter.

Be sure to specify this parameter only for trusted computers.

-TargetAddress<String>

Specifies the name or IP address of the management port on the remote hardware device. For server hardware, this is typically a dedicated Baseboard Management Controller (BMC) IP address. For other devices, like network switches, this is the IP address of their management port. For desktop and mobile devices, the BMC sometimes shares the same IP address as the computer.

-ThrottleLimit<Int32>

Cmdlet을 실행하도록 설정할 수 있는 동시 작업의 최대 수를 지정합니다. 이 매개 변수를 생략하거나 값으로 0 을 입력하면 Windows PowerShell®은 컴퓨터에서 실행 중인 CIM cmdlet의 수에 따라 cmdlet에 대한 최적의 스로틀 제한을 계산합니다. 스로틀 제한은 현재 cmdlet에만 적용되고, 세션이나 컴퓨터에는 적용되지 않습니다.

-TimeoutSec<UInt32>

Specifies how long to wait, in seconds, for a response from the remote hardware device. After this period, the cmdlet abandons the connection attempt.

-UseSSL

Indicates that the server connects to the target computer by using SSL. WS-Management encrypts all content transmitted over the network. Specify this parameter to use the additional protection of HTTPS instead of HTTP. If you specify this parameter and SSL is not available on the connection port, the command fails.

-Confirm

cmdlet을 실행하기 전에 확인 메시지를 표시합니다.

-WhatIf

cmdlet이 실행되는 경우 발생할 결과를 보여 줍니다. cmdlet은 실행되지 않습니다.

<CommonParameters>

이 cmdlet은 -Verbose, -Debug, -ErrorAction, -ErrorVariable, -OutBuffer, -OutVariable 등의 일반 매개 변수를 지원합니다. 자세한 내용은 TechNet의 about_CommonParameters(https://go.microsoft.com/fwlink/p/?LinkID=113216)

입력

입력 형식은 cmdlet으로 파이프할 수 있는 개체의 형식입니다.

• Microsoft.Management.Infrastructure.CimInstance#root/Microsoft/Windows/HardwareManagement/MSFT_PCSVDevice

  A MSFT_PCSVDevice object that is the target for the operation. To obtain a MSFT_PCSVDevice object, use the Get-PcsvDevice cmdlet.

출력

출력 형식은 cmdlet 실행 시 출력되는 개체의 형식입니다.

• Microsoft.Management.Infrastructure.CimInstance#root/Microsoft/Windows/HardwareManagement/MSFT_PCSVDevice

  The cmdlet only returns an MSFT_PCSVDevice object if you specify the PassThru parameter.

예

Example 1: Start a computer by specifying its IP address

This example starts a device. After you execute these commands, the device enters the Enabled state.

The first command uses the Get-Credential cmdlet to create a credential, and then stores it in the $Credential variable. The cmdlet prompts you for a user name and password. For more information, type Get-Help Get-Credential.

The second command starts the target computer that has the management IP address 10.1.12.43 by using the IPMI management protocol. The command specifies the credential object stored in the $Credential variable.

PS C:\> $Credential = Get-Credential
PS C:\> Start-PcsvDevice -TargetAddress "10.1.12.43" -Credential $Credential -ManagementProtocol IPMI

Example 2: Start a computer by specifying it as an object

This example starts a device specified as an object. After you execute these commands, the device enters the Enabled state.

The first command uses the Get-Credential cmdlet to create a credential, and then stores it in the $Credential variable. The cmdlet prompts you for a user name and password. For more information, type Get-Help Get-Credential.

The second command uses the Get-PcsvDevice cmdlet to connect to the computer that has the specified management IP address by using the IPMI management protocol. The command specifies the credential object stored in the $Credential variable. The cmdlet passes that connection to the Start-PcsvDevice cmdlet by using the pipeline operator. That cmdlet starts the device.

PS C:\> $Credential = Get-Credential
PS C:\> Get-PcsvDevice –TargetAddress "10.1.12.43" -Credential $Credential -ManagementProtocol IPMI | Start-PcsvDevice

관련 항목

Get-PcsvDevice

Restart-PcsvDevice

Set-PcsvDeviceBootConfiguration

Stop-PcsvDevice