Set-NetNeighbor

Set-NetNeighbor

Modifies a neighbor cache entry.

구문

Parameter Set: ByName
Set-NetNeighbor [[-IPAddress] <String[]> ] [-AddressFamily <AddressFamily[]> ] [-CimSession <CimSession[]> ] [-IncludeAllCompartments] [-InterfaceAlias <String[]> ] [-InterfaceIndex <UInt32[]> ] [-LinkLayerAddress <String> ] [-PassThru] [-PolicyStore <String> ] [-State <State[]> ] [-ThrottleLimit <Int32> ] [-Confirm] [-WhatIf] [ <CommonParameters>] [ <WorkflowParameters>]

Parameter Set: InputObject (cdxml)
Set-NetNeighbor [-CimSession <CimSession[]> ] [-LinkLayerAddress <String> ] [-PassThru] [-ThrottleLimit <Int32> ] [-Confirm] [-WhatIf] [ <CommonParameters>] [ <WorkflowParameters>]

자세한 설명

The Set-NetNeighbor cmdlet modifies a neighbor cache entry. The neighbor cache maintains information for each on-link neighbor, including the IP address and the associated link-layer address. You can modify only neighbor cache entries that are in a permanent state on interfaces that have link-layer addresses. Use this cmdlet to modify the link-layer address and policy store setting of a neighbor cache entry.

매개 변수

-AddressFamily<AddressFamily[]>

Specifies an array of IP address families. The cmdlet modifies the neighbor cache entries that belong to the IP address families you specify. If you do not specify this parameter, the cmdlet automatically generates the address families of the neighbor cache entries. 이 매개 변수에 허용되는 값은 다음과 같습니다.

-- IPv4
-- IPv6

-CimSession<CimSession[]>

원격 세션이나 원격 컴퓨터에서 cmdlet을 실행합니다. 컴퓨터 이름이나 New-CimSession 또는 Get-CimSession cmdlet의 출력과 같은 세션 개체를 입력하세요. 기본값은 로컬 컴퓨터 상의 현재 세션입니다.

-IncludeAllCompartments

Indicates that the cmdlet includes neighbor cache entries from all configured network compartments. If you do not specify this parameter, the cmdlet modifies only neighbor cache entries in the default network compartment.

-IPAddress<String[]>

Specifies an array of IP addresses. The cmdlet modifies neighbor cache entries that have the IP addresses you specify.

-LinkLayerAddress<String>

Specifies the link-layer address of the neighbor cache entry. The cmdlet modifies the link-layer address of the neighbor cache entry you specify.

The link-layer address is also called the media access control (MAC) address. A link-layer address that uses IPv4 address syntax is a tunnel technology that encapsulates packets over an IPv4 tunnel, such as Intra-Site Automatic Tunnel Addressing Protocol (ISATAP) or Teredo. A link-layer address of all zeroes indicates that the neighbor is unreachable and the neighbor cache entry does not have a link-layer address entry. An empty link-layer address indicates that the link layer does not use link-layer addresses, such as on a loopback interface.

-InterfaceAlias<String[]>

Specifies an array of aliases of network interfaces. The cmdlet modifies neighbor cache entries for the network interfaces that have the aliases you specify.

-InterfaceIndex<UInt32[]>

Specifies an array of indexes of network interfaces. The cmdlet modifies neighbor cache entries for the network interfaces located at the indexes you specify.

-PassThru

작업 중인 항목을 나타내는 개체를 반환합니다. 기본적으로 이 cmdlet은 출력을 생성하지 않습니다.

-PolicyStore<String>

Specifies a PolicyStore value. The cmdlet modifies the PolicyStore setting for the neighbor cache entry to the value you specify. 이 매개 변수에 허용되는 값은 다음과 같습니다.

-- ActiveStore: The IP address information is valid.
-- PersistentStore: The computer saves IP address information across restarts. When the computer restarts, it copies the saved settings to the ActiveStore.

Specify ActiveStore only.

If you do not specify this parameter, the default entries are created in both the ActiveStore and the PersistentStore.

-State<State[]>

Specifies an array of states of the neighbor cache entry. The cmdlet modifies the neighbor cache entries that have the states you specify. You can modify only neighbor cache entries that are in a permanent state. 이 매개 변수에 허용되는 값은 다음과 같습니다.

-- Permanent. The neighbor is statically provisioned and will not expire unless you remove it.

-ThrottleLimit<Int32>

Cmdlet을 실행하도록 설정할 수 있는 동시 작업의 최대 수를 지정합니다. 이 매개 변수를 생략하거나 값으로 0 을 입력하면 Windows PowerShell®은 컴퓨터에서 실행 중인 CIM cmdlet의 수에 따라 cmdlet에 대한 최적의 스로틀 제한을 계산합니다. 스로틀 제한은 현재 cmdlet에만 적용되고, 세션이나 컴퓨터에는 적용되지 않습니다.

-Confirm

cmdlet을 실행하기 전에 확인 메시지를 표시합니다.

-WhatIf

cmdlet이 실행되는 경우 발생할 결과를 보여 줍니다. cmdlet은 실행되지 않습니다.

<CommonParameters>

이 cmdlet은 -Verbose, -Debug, -ErrorAction, -ErrorVariable, -OutBuffer, -OutVariable 등의 일반 매개 변수를 지원합니다. 자세한 내용은 TechNet의 about_CommonParameters(https://go.microsoft.com/fwlink/p/?LinkID=113216)

<WorkflowParameters>

입력

입력 형식은 cmdlet으로 파이프할 수 있는 개체의 형식입니다.

• Microsoft.Management.Infrastructure.CimInstance#root\StandardCimv2\MSFT_NetNeighbor

  Microsoft.Management.Infrastructure.CimInstance 개체는 WMI(Windows Management Instrumentation) 개체를 표시하는 래퍼 클래스입니다. 파운드 기호(#) 뒤의 경로는 기본 WMI 개체에 대한 네임 스페이스 및 클래스 이름을 제공합니다.

출력

출력 형식은 cmdlet 실행 시 출력되는 개체의 형식입니다.

• None

예

Example 1: Set the link-layer address for a neighbor cache entry

This command sets the link-layer address for the neighbor cache entry that has the IP address 192.168.0.5 and the interface index value of 12.

PS C:\> Set-NetNeighbor –InterfaceIndex 12 –IPAddress "192.168.0.5" –LinkLayerAddress "00-00-12-00-00-ff"

Example 2: Set the link-layer address for a neighbor cache entry by using an input object

This command gets the NetNeighbor object that has the IP address 192.168.0.5 and the interface index value of 12. The command passes the object to the Set-NetNeighbor cmdlet by using the pipeline operator. Set-NetNeighbor sets the link-layer address for the neighbor cache entry to 00-00-12-00-00-ff.

PS C:\> Get-NetNeighbor –InterfaceIndex 12 –IPAddress "192.168.0.5" | Set-NetNeighbor –LinkLayerAddress "00-00-12-00-00-ff"

관련 항목

Get-NetNeighbor

New-NetNeighbor

Remove-NetNeighbor