Remove-RemoteAccessRadius

Remove-RemoteAccessRadius

Removes an external RADIUS server from being used for VPN authentication, accounting for both DirectAccess (DA) and VPN, or one-time password (OTP) authentication for DA.

구문

Parameter Set: Remove2
Remove-RemoteAccessRadius [-ServerName] <String> [-Purpose] <String> {Authentication | Accounting | Otp} [-CimSession <CimSession[]> ] [-ComputerName <String> ] [-EntrypointName <String> ] [-InformationAction <System.Management.Automation.ActionPreference> {SilentlyContinue | Stop | Continue | Inquire | Ignore | Suspend} ] [-InformationVariable <System.String> ] [-PassThru] [-ThrottleLimit <Int32> ] [-Confirm] [-WhatIf] [ <CommonParameters>] [ <WorkflowParameters>]

자세한 설명

The Remove-RemoteAccessRadius cmdlet removes an external RADIUS server from being used for VPN authentication, Accounting for both DirectAccess (DA) and VPN, or one-time password (OTP) authentication for DA as follows.
-- Accounting RADIUS configuration applies to both DA and VPN.
-- OTP RADIUS configuration applies only to DA.
-- Authentication RADIUS configuration applies only to VPN.

A RADIUS server configuration for Accounting and OTP are global in nature, such that the configurations apply to the entire Remote Access deployment. RADIUS server configuration for VPN applies only to a specific VPN server, and all servers in a load balancing cluster, or if multi-site is deployed, to all VPN servers at a site.

The following behaviors describe aspects of this cmdlet.
-- If a RADIUS server is currently being used for multiple purposes, then it can be removed for one or more of the purposes. However, the cmdlet would have to be run separately for each purpose.
-- If the last RADIUS server being used for accounting is removed, then the accounting type automatically switches to Windows accounting.
-- The User is not allowed to delete the last RADIUS server being used for VPN authentication if Radius authentication is configured.
-- When RADIUS accounting or RADIUS authentication is disabled, using the Set-RemoteAccessAccounting and Set-VpnAuthType cmdlets, then the RADIUS servers is use do not show up in the configuration and therefore cannot be explicitly removed.

매개 변수

-CimSession<CimSession[]>

원격 세션이나 원격 컴퓨터에서 cmdlet을 실행합니다. 컴퓨터 이름이나 New-CimSession 또는 Get-CimSession cmdlet의 출력과 같은 세션 개체를 입력하세요. 기본값은 로컬 컴퓨터 상의 현재 세션입니다.

-ComputerName<String>

Specifies the IPv4 or IPv6 address, or host name, of the computer on which the Remote Access server computer specific tasks should be run. If this parameter is specified when removing a RADIUS server for authentication, then it is removed for the VPN server represented by this parameter.

-EntrypointName<String>

Specifies a site in a multi-site deployment. It is applicable only to RADIUS server configuration for VPN authentication. It is not applicable to RADIUS accounting and OTP.
When the parameter is specified it indicates that the Radius server for VPN authentication should be removed for that site.
If this parameter is not specified in a multi-site deployment, then this parameter value on which the cmdlet is run is used. The server could also be represented by using the ComputerName parameter.
If this parameter and ComputerName are specified and the ComputerName does not belong to the site represented by this parameter, then this parameter takes precedence and the RADIUS server is removed from it.

-InformationAction<System.Management.Automation.ActionPreference>

-InformationVariable<System.String>

-PassThru

작업 중인 항목을 나타내는 개체를 반환합니다. 기본적으로 이 cmdlet은 출력을 생성하지 않습니다.

-Purpose<String>

Specifies the purpose for which the external RADIUS server is being removed. 이 매개 변수에 허용되는 값은 다음과 같습니다.
-- Authentication.
-- Accounting.
-- Otp.

-ServerName<String>

Specifies the IPv4 or IPv6 address, or host name, of the external RADIUS server that needs to be removed.

-ThrottleLimit<Int32>

Cmdlet을 실행하도록 설정할 수 있는 동시 작업의 최대 수를 지정합니다. 이 매개 변수를 생략하거나 값으로 0 을 입력하면 Windows PowerShell®은 컴퓨터에서 실행 중인 CIM cmdlet의 수에 따라 cmdlet에 대한 최적의 스로틀 제한을 계산합니다. 스로틀 제한은 현재 cmdlet에만 적용되고, 세션이나 컴퓨터에는 적용되지 않습니다.

-Confirm

cmdlet을 실행하기 전에 확인 메시지를 표시합니다.

-WhatIf

cmdlet이 실행되는 경우 발생할 결과를 보여 줍니다. cmdlet은 실행되지 않습니다.

<CommonParameters>

이 cmdlet은 -Verbose, -Debug, -ErrorAction, -ErrorVariable, -OutBuffer, -OutVariable 등의 일반 매개 변수를 지원합니다. 자세한 내용은 TechNet의 about_CommonParameters(https://go.microsoft.com/fwlink/p/?LinkID=113216)

<WorkflowParameters>

입력

입력 형식은 cmdlet으로 파이프할 수 있는 개체의 형식입니다.

• None

출력

출력 형식은 cmdlet 실행 시 출력되는 개체의 형식입니다.

• Microsoft.Management.Infrastructure.CimInstance#RemoteAccessRadiusServerPurpose[]

  Microsoft.Management.Infrastructure.CimInstance 개체는 WMI(Windows Management Instrumentation) 개체를 표시하는 래퍼 클래스입니다. 파운드 기호(#) 뒤의 경로는 기본 WMI 개체에 대한 네임 스페이스 및 클래스 이름을 제공합니다.
  The array of RemoteAccessRadiusServerPurpose objects consists of the following properties:
  -- The IPv4 or IPv6 address of the RADIUS server that was removed.
  -- The purpose for which the server was removed.

예

EXAMPLE 1

This example removes a RADIUS server from being used for authentication. The RADIUS server named 10.1.1.1 is being used for both authentication and accounting. This cmdlet removes the server from being used for authentication.

PS C:\> Get-RemoteAccessRadius

PS C:\> Remove-RemoteAccessRadius -ServerName 10.1.1.1 -Purpose Authentication -PassThru

PS C:\> Get-RemoteAccessRadius

관련 항목

Set-RemoteAccessAccounting

Set-VpnAuthType