Get-DAServer

Get-DAServer

Displays the properties of the DirectAccess (DA) server.

구문

Parameter Set: Get0
Get-DAServer [[-EntrypointName] <String> ] [-AsJob] [-CimSession <CimSession[]> ] [-ComputerName <String> ] [-ThrottleLimit <Int32> ] [ <CommonParameters>]

자세한 설명

The Get-DAServer cmdlet displays the properties of the DirectAccess (DA) server.

The output displayed consists of the following.

Global Configuration: These properties are applicable to the entire DA deployment.
-- DA installation configuration: full install or only manage-out.
-- Internal IPv6 prefix.
-- Authentication type.
-- IPsec root certificate: The certificate is always configured separately on every server, although the same certificate issued by same root is present on all DA servers.
-- Intermediate root certificate usage: enabled or disabled.
-- Computer certificate authentication: enabled or disabled.
-- DA server GPO name.
-- Health check: enabled or disabled.

For the following properties either the server-level or cluster level, if load balancing has been deployed, configuration is returned. If multi-site is deployed, then this configuration is applicable at the site-level and configuration for the specified site is displayed.
-- Client IPv6 prefix.
-- Teredo State.
-- Whether NAT is enabled.
-- Does DA server have a single network adapter or two network adapters.

The following are pure server-level properties that are returned. In a multi-site deployment if both the EntryPointName and ComputerName parameters are specified, but the ComputerName parameter value does not belong to that entry point name, then no values are returned for these properties. However, if only the EntryPointName parameter is specified or the ComputerName parameter value is also specified and belongs to the specified entry point name, then the configuration is retrieved from the server on which the cmdlet is run as follows.
-- Internet interface.
-- Internal interface.
-- SSL certificate.

매개 변수

-AsJob

-CimSession<CimSession[]>

원격 세션에서 또는 원격 컴퓨터에서 cmdlet을 실행합니다. New-CimSession 또는 Get-CimSession cmdlet의 출력과 같은 컴퓨터 이름이나 세션 개체를 입력합니다. 기본값은 로컬 컴퓨터의 현재 세션입니다.

-ComputerName<String>

Specifies the IPv4 or IPv6 address, or host name, of the computer on which the DA server computer specific tasks should be run.

-EntrypointName<String>

Specifies the identity of a site in a multi-site deployment and when specified indicates that the configuration of the DA server at that site should be retrieved.
If this parameter is not specified in a multi-site deployment then the entry point to which the server on which this cmdlet is run is used. The server could also be represented by using the ComputerName parameter.
If both this parameter and ComputerName parameter are specified and the computer name does not belong to the site represented by this parameter then this parameter takes precedence and the configuration is returned for it.

-ThrottleLimit<Int32>

이 cmdlet을 실행하도록 설정할 수 있는 최대 동시 작업 수를 지정합니다. 이 매개 변수가 생략되거나 값 0이 입력되면 Windows PowerShell®은 컴퓨터에서 실행 중인 CIM cmdlet의 수에 따라 cmdlet에 대한 최적의 제한 한도를 계산합니다. 제한 한도는 현재 cmdlet에만 적용되며 세션이나 컴퓨터에는 적용되지 않습니다.

<CommonParameters>

이 cmdlet은 일반 매개 변수 -Verbose, -Debug, -ErrorAction, -ErrorVariable, -OutBuffer 및 -OutVariable을 지원합니다. 자세한 내용은 다음을 참조하세요. about_CommonParameters(https://go.microsoft.com/fwlink/p/?LinkID=113216).

입력

입력 유형은 cmdlet에 파이프할 수 있는 개체의 유형입니다.

• None

출력

출력 유형은 cmdlet이 내보내는 개체의 유형입니다.

• Microsoft.Management.Infrastructure.CimInstance#MSFT_DAServer

  Microsoft.Management.Infrastructure.CimInstance 개체는 WMI(Windows Management Instrumentation) 개체를 표시하는 래퍼 클래스입니다. 파운드 기호(#) 뒤에 오는 경로는 기본 WMI 개체의 네임스페이스 및 클래스 이름을 제공합니다.
  The output object contains the following properties:
  -- Type of DA installation: full or managed.
  -- Authentication type.
  -- Internal IPv6 prefix.
  -- Client IPHTTPS IPv6 prefix.
  -- Usage of computer certificate authorization for 1st tunnel: Enabled or Disabled.
  -- IPsec root certificate.
  -- Whether the IPsec root certificate is an intermediate root certificate.
  -- Status of Teredo: Enabled or Disabled.
  -- Whether the DA server is deployed behind NAT.
  -- Whether the configuration in which DA is deployed is a single or double network adapter.
  -- Name of the DA server GPO.
  -- Status of the health check.

예제

EXAMPLE 1

This example displays the properties of the local DA server.

PS C:\> Get-DAServer

관련 항목

Get-DAServer

Get-RemoteAccess