Set-VpnIPAddressAssignment

Set-VpnIPAddressAssignment

Configures the IPv4 address assignment method or the IPv6 prefix for IPv6 address assignment.

구문

Parameter Set: VpnIPAddressAssignment
Set-VpnIPAddressAssignment [-CimSession <CimSession[]> ] [-ComputerName <String> ] [-InformationAction <System.Management.Automation.ActionPreference> {SilentlyContinue | Stop | Continue | Inquire | Ignore | Suspend} ] [-InformationVariable <System.String> ] [-IPAddressRange <String[]> ] [-IPAssignmentMethod <String> {Dhcp | StaticPool} ] [-IPv6Prefix <String> ] [-PassThru] [-ThrottleLimit <Int32> ] [-Confirm] [-WhatIf] [ <CommonParameters>] [ <WorkflowParameters>]

Parameter Set: VpnIPv6PrefixEntrypoint
Set-VpnIPAddressAssignment -EntrypointName <String> -IPv6Prefix <String> [-CimSession <CimSession[]> ] [-ComputerName <String> ] [-InformationAction <System.Management.Automation.ActionPreference> {SilentlyContinue | Stop | Continue | Inquire | Ignore | Suspend} ] [-InformationVariable <System.String> ] [-PassThru] [-ThrottleLimit <Int32> ] [-Confirm] [-WhatIf] [ <CommonParameters>] [ <WorkflowParameters>]

자세한 설명

The Set-VpnIPAddressAssignment cmdlet is only used to toggle from one IPv4 address assignment type to another. This cmdlet cannot be used to add additional IPv4 address ranges if a static pool IP address assignment is being used.
-- This cmdlet cannot be used to Enable or Disable an IPv4 or IPv6 address assignment.

매개 변수

-CimSession<CimSession[]>

원격 세션이나 원격 컴퓨터에서 cmdlet을 실행합니다. 컴퓨터 이름이나 New-CimSession 또는 Get-CimSession cmdlet의 출력과 같은 세션 개체를 입력하세요. 기본값은 로컬 컴퓨터 상의 현재 세션입니다.

-ComputerName<String>

Specifies the IPv4 or IPv6 address, or host name, of the computer on which the VPN server computer specific tasks should be run. If this parameter is specified, then the address assignment properties are configured for that VPN server.

-EntrypointName<String>

Specifies a site in a multi-site deployment for which the IPv6 prefix needs to be configured. This parameter is not applicable to the IPv4 address assignment properties as these properties are always configured at the individual server level and not site level.
If this parameter is not specified in a multi-site deployment, then this parameter value to which the cmdlet is run is used. The server could also be represented by using the ComputerName parameter.
If this parameter and the ComputerName parameter are specified and the ComputerName does not belong to the site represented by this parameter, then this parameter takes precedence and the authentication type is configured for it.

-InformationAction<System.Management.Automation.ActionPreference>

-InformationVariable<System.String>

-IPAddressRange<String[]>

Specifies the IP address range from which IP addresses are allocated to VPN clients. Consists of a starting IP and an ending IP. This parameter can be configured only if the IPAssignmentMethod parameter is specified to be StaticPool.
If there are no pre-existing IPv4 address pools, then it is mandatory to specify an address range.

-IPAssignmentMethod<String>

Specifies the mechanism for IPv4 address assignment. 이 매개 변수에 허용되는 값은 다음과 같습니다.
-- Dhcp.
-- StaticPool.
When load balancing is active the IPv4 address assignment method cannot be configured to DHCP. Only a static pool is supported.

-IPv6Prefix<String>

Specifies the IPv6 prefix used for IPv6 address assignment.

-PassThru

작업 중인 항목을 나타내는 개체를 반환합니다. 기본적으로 이 cmdlet은 출력을 생성하지 않습니다.

-ThrottleLimit<Int32>

Cmdlet을 실행하도록 설정할 수 있는 동시 작업의 최대 수를 지정합니다. 이 매개 변수를 생략하거나 값으로 0 을 입력하면 Windows PowerShell®은 컴퓨터에서 실행 중인 CIM cmdlet의 수에 따라 cmdlet에 대한 최적의 스로틀 제한을 계산합니다. 스로틀 제한은 현재 cmdlet에만 적용되고, 세션이나 컴퓨터에는 적용되지 않습니다.

-Confirm

cmdlet을 실행하기 전에 확인 메시지를 표시합니다.

-WhatIf

cmdlet이 실행되는 경우 발생할 결과를 보여 줍니다. cmdlet은 실행되지 않습니다.

<CommonParameters>

이 cmdlet은 -Verbose, -Debug, -ErrorAction, -ErrorVariable, -OutBuffer, -OutVariable 등의 일반 매개 변수를 지원합니다. 자세한 내용은 TechNet의 about_CommonParameters(https://go.microsoft.com/fwlink/p/?LinkID=113216)

<WorkflowParameters>

입력

입력 형식은 cmdlet으로 파이프할 수 있는 개체의 형식입니다.

• None

출력

출력 형식은 cmdlet 실행 시 출력되는 개체의 형식입니다.

• Microsoft.Management.Infrastructure.CimInstance#VpnIPAddressAssignment

  Microsoft.Management.Infrastructure.CimInstance 개체는 WMI(Windows Management Instrumentation) 개체를 표시하는 래퍼 클래스입니다. 파운드 기호(#) 뒤의 경로는 기본 WMI 개체에 대한 네임 스페이스 및 클래스 이름을 제공합니다.
  The object consists of the following properties:
  -- The IPv4 assignment method configured: DHCP or static pool.
  -- If static pool assignment is configured for IPv4, then the list of configured address pools. Each pool consists of a starting IP address and an ending IP address.
  -- The IPv6 prefix configured.

예

EXAMPLE 1

This cmdlet sets the IPv4 address assignment type to be DHCP which causes IPv4 address assignment to happen from a DHCP server.

PS C:\> Set-VpnIPAddressAssignment -IPAssignmentMethod "Dhcp" -PassThru

EXAMPLE 2

The cmdlet specifies the IPv4 address assignment to happen from the IP range 30.1.1.10 through 30.1.1.30. IPv6 prefix 2002:836b:2:1000::/64 is used for IPv6 address assignment. Changing the IPv6 prefix requires the remote access service to be restarted in order to take effect. This is conveyed through the warning message.

PS C:\> Set-VpnIPAddressAssignment -IPAssignmentMethod "StaticPool" -IPAddressRange "30.1.1.10", "30.1.1.30" -IPv6Prefix "2002:836b:2:1000::/64" -PassThru

관련 항목

Add-VpnIPAddressRange

Remove-VpnIPAddressRange