Get-RemoteAccessHealth

Get-RemoteAccessHealth

Obtains the current health of a RemoteAccess (RA) deployment.

구문

Parameter Set: Cluster
Get-RemoteAccessHealth [-AsJob] [-CimSession <CimSession[]> ] [-Cluster] [-ComputerName <String> ] [-Refresh] [-ThrottleLimit <Int32> ] [ <CommonParameters>]

Parameter Set: EntrypointName
Get-RemoteAccessHealth -EntrypointName <String> [-AsJob] [-CimSession <CimSession[]> ] [-ComputerName <String> ] [-Refresh] [-ThrottleLimit <Int32> ] [ <CommonParameters>]

자세한 설명

The Get-RemoteAccessHealth cmdlet obtains the current health of a RemoteAccess (RA) deployment as follows.
-- Health of a specific Remote Access server.
-- Health of a load balancing cluster.
-- Health of a site, in case of a multi-site deployment: this again corresponds to the health of a single server or health of a cluster at that site.

The health information returned for a single server consists of the following.
-- Server address.
-- Rolled up health of the server: This depends on the health of the individual technology features that RA is comprised. The following rule applies: If all features are healthy, then the server is healthy. If one or more features are in the yellow health state, then the health of the server is also yellow. If one or more features are in the red health state, then the health of the server is also red; this applies even if one or more features are in yellow health state.
-- Time stamp when the health of the server changed.
-- Health of the individual RA features. This comprises of the following.
---- Health state of a feature: The roll-up of the health of individual pre-defined monitors that determine the health of the feature. Every monitor causes the feature to go into red or yellow health. If multiple monitors are unhealthy, then the roll-up rules are similar to the one for server health roll-up defined above.
---- Time stamp when the health of the feature last changed.
---- If a DA feature is not healthy, then the details of the monitors that are unhealthy.

The health information returned for a cluster is quite similar to the server health and consists of the following.
-- Rolled up health of cluster: This depends on the health of each of the servers present in the cluster. The roll-up rules are similar to the feature health roll-up for server.
-- Time stamp when health of the cluster changed.
-- Health of the individual servers in the cluster: The health information described above is returned for each of the servers.

매개 변수

-AsJob

-CimSession<CimSession[]>

원격 세션에서 또는 원격 컴퓨터에서 cmdlet을 실행합니다. New-CimSession 또는 Get-CimSession cmdlet의 출력과 같은 컴퓨터 이름이나 세션 개체를 입력합니다. 기본값은 로컬 컴퓨터의 현재 세션입니다.

-Cluster

Indicates that the cmdlet gets the health for the entire cluster. If you specify both this parameter and the ComputerName parameter, the cmdlet gets the health of the cluster to which the computer belongs. If you specify this parameter in a multisite scenario, the cmdlet gets the health of the cluster in the site for the server on which you run the cmdlet. You can use the ComputerName parameter to specify the computer that runs the cmdlet.

-ComputerName<String>

Indicates the IPv4 or IPv6 address, or host name, of the computer on which this cmdlet needs to be run and the health retrieved. When this parameter is specified, then the health of that RA server is returned.

-EntrypointName<String>

Specifies the identity of a site in a multi-site deployment whose health needs to be retrieved.
If both this parameter and ComputerName parameter are specified and the computer name does not belong to the site represented by the entry point name, then this parameter takes precedence and the site health is retrieved.

-Refresh

Indicates that the cmdlet recomputes the health details for the computer, cluster, or entry point that you specify for the cmdlet.

-ThrottleLimit<Int32>

이 cmdlet을 실행하도록 설정할 수 있는 최대 동시 작업 수를 지정합니다. 이 매개 변수가 생략되거나 값 0이 입력되면 Windows PowerShell®은 컴퓨터에서 실행 중인 CIM cmdlet의 수에 따라 cmdlet에 대한 최적의 제한 한도를 계산합니다. 제한 한도는 현재 cmdlet에만 적용되며 세션이나 컴퓨터에는 적용되지 않습니다.

<CommonParameters>

이 cmdlet은 일반 매개 변수 -Verbose, -Debug, -ErrorAction, -ErrorVariable, -OutBuffer 및 -OutVariable을 지원합니다. 자세한 내용은 다음을 참조하세요. about_CommonParameters(https://go.microsoft.com/fwlink/p/?LinkID=113216).

입력

입력 유형은 cmdlet에 파이프할 수 있는 개체의 유형입니다.

• None

출력

출력 유형은 cmdlet이 내보내는 개체의 유형입니다.

• Microsoft.Management.Infrastructure.CimInstance#RemoteAccessHealthMonitor[]

  Microsoft.Management.Infrastructure.CimInstance 개체는 WMI(Windows Management Instrumentation) 개체를 표시하는 래퍼 클래스입니다. 파운드 기호(#) 뒤에 오는 경로는 기본 WMI 개체의 네임스페이스 및 클래스 이름을 제공합니다.
  The array of RemoteAccessHealthMonitor objects consists of the following properties for cluster, server and components of the server:
  -- Component name
  -- Remote Access server address
  -- HealthState
  -- TimeStamp
  -- OperationStatus
  -- ID
  -- ErrorDesc
  -- ErrorCause
  -- ErrorResoln

예제

EXAMPLE 1

This example displays the health of a specific server.

PS C:\> Get-RemoteAccessHealth

EXAMPLE 2

This example displays the health of a cluster containing two Remote Access servers.

PS C:\> Get-RemoteAccessHealth –Cluster

관련 항목

Get-DAServer

Get-RemoteAccess