Security Bulletin

Microsoft Security Bulletin MS10-015 - Important

Vulnerabilities in Windows Kernel Could Allow Elevation of Privilege (977165)

Published: February 09, 2010 | Updated: March 17, 2010

Version: 1.3

General Information

Executive Summary

This security update resolves one publicly disclosed and one privately reported vulnerability in Microsoft Windows. The vulnerabilities could allow elevation of privilege if an attacker logged on to the system and then ran a specially crafted application. To exploit either vulnerability, an attacker must have valid logon credentials and be able to log on locally. The vulnerabilities could not be exploited remotely or by anonymous users.

This security update is rated Important for all supported editions of Microsoft Windows 2000, Windows XP, Windows Server 2003, Windows Vista, Windows Server 2008, and Windows 7 for 32-bit Systems. For more information, see the subsection, Affected and Non-Affected Software, in this section.

The security update addresses the vulnerabilities by ensuring that the Windows Kernel handles exceptions properly. For more information about the vulnerabilities, see the Frequently Asked Questions (FAQ) subsection for the specific vulnerability entry under the next section, Vulnerability Information.

This security update also addresses the vulnerability first described in Microsoft Security Advisory 979682.

Recommendation. The majority of customers have automatic updating enabled and will not need to take any action because this security update will be downloaded and installed automatically. Customers who have not enabled automatic updating need to check for updates and install this update manually. For information about specific configuration options in automatic updating, see Microsoft Knowledge Base Article 294871.

For administrators and enterprise installations, or end users who want to install this security update manually, Microsoft recommends that customers apply the update at the earliest opportunity using update management software, or by checking for updates using the Microsoft Update service.

See also the section, Detection and Deployment Tools and Guidance, later in this bulletin.

Known Issues. Microsoft Knowledge Base Article 977165 documents the currently known issues that customers may experience when installing this security update. The article also documents recommended solutions for these issues. When currently known issues and recommended solutions pertain only to specific releases of this software, this article provides links to further articles.

Affected and Non-Affected Software

The following software have been tested to determine which versions or editions are affected. Other versions or editions are either past their support life cycle or are not affected. To determine the support life cycle for your software version or edition, visit Microsoft Support Lifecycle.

Affected Software

Operating System Maximum Security Impact Aggregate Severity Rating Bulletins Replaced by this Update
Microsoft Windows 2000 Service Pack 4 Elevation of Privilege Important MS09-058
Windows XP Service Pack 2 and Windows XP Service Pack 3 Elevation of Privilege Important MS09-058
Windows XP Professional x64 Edition Service Pack 2 Elevation of Privilege Important MS09-058
Windows Server 2003 Service Pack 2 Elevation of Privilege Important MS09-058
Windows Server 2003 x64 Edition Service Pack 2 Elevation of Privilege Important MS09-058
Windows Server 2003 with SP2 for Itanium-based Systems Elevation of Privilege Important MS09-058
Windows Vista, Windows Vista Service Pack 1, and Windows Vista Service Pack 2 Elevation of Privilege Important MS09-058
Windows Vista x64 Edition, Windows Vista x64 Edition Service Pack 1, and Windows Vista x64 Edition Service Pack 2 Elevation of Privilege Important MS09-058
Windows Server 2008 for 32-bit Systems and Windows Server 2008 for 32-bit Systems Service Pack 2* Elevation of Privilege Important MS09-058
Windows Server 2008 for x64-based Systems and Windows Server 2008 for x64-based Systems Service Pack 2* Elevation of Privilege Important MS09-058
Windows Server 2008 for Itanium-based Systems and Windows Server 2008 for Itanium-based Systems Service Pack 2 Elevation of Privilege Important MS09-058
Windows 7 for 32-bit Systems Elevation of Privilege Important None

*Server Core installation affected. This update applies, with the same severity rating, to supported editions of Windows Server 2008 or Windows Server 2008 R2 as indicated, whether or not installed using the Server Core installation option. For more information on this installation option, see the MSDN articles, Server Core and Server Core for Windows Server 2008 R2. Note that the Server Core installation option does not apply to certain editions of Windows Server 2008 and Windows Server 2008 R2; see Compare Server Core Installation Options.

Non-Affected Software

Operating System
Windows 7 for x64-based Systems
Windows Server 2008 R2 for x64-based Systems
Windows Server 2008 R2 for Itanium-based Systems

Why was this bulletin revised on March 2, 2010?
Microsoft revised this bulletin to announce the offering of revised packages on Windows Update for the MS10-015 update. This revision is due to a change in the package installation logic that prevents the installation of the security update if certain abnormal conditions exist on a system. These abnormal conditions on a system could be the result of an infection with a computer virus that modifies some operating system files, which renders the infected computer incompatible with the MS10-015 update. In some instances, installing security update MS10-015 on an infected computer could cause the computer to restart repeatedly. For more information about this issue, see the following Web page. This is a change to the package installation logic on updates distributed through Windows Update only; there were no changes to the security update binaries or to the Windows Update detection logic. The updates available on the Microsoft Download Center have not changed and do not contain this new package installation logic. Customers who have already successfully updated their systems, including customers with automatic updating enabled, do not need to take any action. Customers with automatic updating enabled, who have not installed this update previously, should consider applying the update at the earliest opportunity.

Where are the file information details?
Refer to the reference tables in the Security Update Deployment section for the location of the file information details.

Why does this update address several reported security vulnerabilities?
This update contains support for several vulnerabilities because the modifications that are required to address these issues are located in related files. Instead of having to install several updates that are almost the same, customers need to install this update only.

Does this update contain any non-security related changes to functionality?
Yes, the update package for all affected Windows platforms (KB977165) includes the changes to the Windows Kernel described in Microsoft Knowledge Base Article 977165.

I am using an older release of the software discussed in this security bulletin. What should I do?
The affected software listed in this bulletin have been tested to determine which releases are affected. Other releases are past their support life cycle. For more information about the product lifecycle, visit the Microsoft Support Lifecycle Web site.

It should be a priority for customers who have older releases of the software to migrate to supported releases to prevent potential exposure to vulnerabilities. To determine the support lifecycle for your software release, see Select a Product for Lifecycle Information. For more information about service packs for these software releases, see Lifecycle Supported Service Packs.

Customers who require custom support for older software must contact their Microsoft account team representative, their Technical Account Manager, or the appropriate Microsoft partner representative for custom support options. Customers without an Alliance, Premier, or Authorized Contract can contact their local Microsoft sales office. For contact information, visit the Microsoft Worldwide Information Web site, select the country in the Contact Information list, and then click Go to see a list of telephone numbers. When you call, ask to speak with the local Premier Support sales manager. For more information, see the Microsoft Support Lifecycle Policy FAQ.

Vulnerability Information

Severity Ratings and Vulnerability Identifiers

The following severity ratings assume the potential maximum impact of the vulnerability. For information regarding the likelihood, within 30 days of this security bulletin's release, of the exploitability of the vulnerability in relation to its severity rating and security impact, please see the Exploitability Index in the February bulletin summary. For more information, see Microsoft Exploitability Index.

Affected Software Windows Kernel Exception Handler Vulnerability - CVE-2010-0232 Windows Kernel Double Free Vulnerability - CVE-2010-0233 Aggregate Severity Rating
Microsoft Windows 2000 Service Pack 4 Important \ Elevation of Privilege Important \ Elevation of Privilege Important
Windows XP Service Pack 2 and Windows XP Service Pack 3 Important \ Elevation of Privilege Important \ Elevation of Privilege Important
Windows XP Professional x64 Edition Service Pack 2 Not applicable Important \ Elevation of Privilege Important
Windows Server 2003 Service Pack 2 Important \ Elevation of Privilege Important \ Elevation of Privilege Important
Windows Server 2003 x64 Edition Service Pack 2 Not applicable Important \ Elevation of Privilege Important
Windows Server 2003 with SP2 for Itanium-based Systems Not applicable Important \ Elevation of Privilege Important
Windows Vista, Windows Vista Service Pack 1, and Windows Vista Service Pack 2 Important \ Elevation of Privilege Important \ Elevation of Privilege Important
Windows Vista x64 Edition, Windows Vista x64 Edition Service Pack 1, and Windows Vista x64 Edition Service Pack 2 Not applicable Important \ Elevation of Privilege Important
Windows Server 2008 for 32-bit Systems and Windows Server 2008 for 32-bit Systems Service Pack 2* Important \ Elevation of Privilege Important \ Elevation of Privilege Important
Windows Server 2008 for x64-based Systems and Windows Server 2008 for x64-based Systems Service Pack 2* Not applicable Important \ Elevation of Privilege Important
Windows Server 2008 for Itanium-based Systems and Windows Server 2008 for Itanium-based Systems Service Pack 2 Not applicable Important \ Elevation of Privilege Important
Windows 7 for 32-bit Systems Important \ Elevation of Privilege Not applicable Important

*Server Core installation affected. This update applies, with the same severity rating, to supported editions of Windows Server 2008 and Windows Server 2008 R2, whether or not installed using the Server Core installation option. For more information on this installation option, see the MSDN articles, Server Core and Server Core for Windows Server 2008 R2. Note that the Server Core installation option does not apply to certain editions of Windows Server 2008 and Windows Server 2008 R2; see Compare Server Core Installation Options.

Windows Kernel Exception Handler Vulnerability - CVE-2010-0232

An elevation of privilege vulnerability exists in the Windows Kernel due to the way the kernel handles certain exceptions. An attacker who successfully exploited this vulnerability could run arbitrary code in kernel mode. An attacker could then install programs; view, change, or delete data; or create new accounts with full user rights.

To view this vulnerability as a standard entry in the Common Vulnerabilities and Exposures list, see CVE-2010-0232.

Mitigating Factors for Windows Kernel Exception Handler Vulnerability - CVE-2010-0232

Mitigation refers to a setting, common configuration, or general best-practice, existing in a default state, that could reduce the severity of exploitation of a vulnerability. The following mitigating factors may be helpful in your situation:

  • 64-bit Microsoft Windows operating systems are not affected by this vulnerability.
  • An attacker must have valid logon credentials and be able to log on locally to exploit this vulnerability. The vulnerability could not be exploited remotely or by anonymous users.

Workarounds for Windows Kernel Exception Handler Vulnerability - CVE-2010-0232

Workaround refers to a setting or configuration change that does not correct the underlying vulnerability but would help block known attack vectors before you apply the update. Microsoft has tested the following workarounds and states in the discussion whether a workaround reduces functionality:

  • Disable the NTVDM subsystem

    Note See Microsoft Knowledge Base Article 979682 for information on how to implement this workaround automatically.

    1. Click Start, click Run, type gpedit.msc in the Open box, and then click OK.
      This opens the Group Policy console.
    2. Expand the Administrative Templates folder, and then click Windows Components.
    3. Click the Application Compatibility folder.
    4. In the details pane, double click the Prevent access to 16-bit applications policy setting. By default, this is set to Not Configured.
    5. Change the policy setting to Enabled, and then click OK.

    Impact of workaround. Users will not be able to run 16-bit applications.

FAQ for Windows Kernel Exception Handler Vulnerability - CVE-2010-0232

What is the scope of the vulnerability?
This is an elevation of privilege vulnerability. An attacker who successfully exploited this vulnerability could execute arbitrary code and take complete control of an affected system. An attacker could then install programs; view, change, or delete data; or create new accounts with full user rights.

What causes the vulnerability?
The Windows kernel does not properly handle certain exceptions.

What is the Windows Kernel?
The Windows Kernel is the core of the operating system. It provides system level services such as device management and memory management, allocates processor time to processes, and manages error handling.

What is the Windows Virtual DOS Machine (NTVDM) subsystem?
The Windows Virtual DOS Machine (NTVDM) subsystem is a protected environment subsystem that emulates MS-DOS and 16-bit Windows within Windows NT-based operating systems. A VDM is created whenever a user starts an MS-DOS application on a Windows NT-based operating system.

What might an attacker use the vulnerability to do?
An attacker who successfully exploited this vulnerability could run arbitrary code in kernel mode. An attacker could then install programs; view, change, or delete data; or create new accounts with full user rights.

How could an attacker exploit the vulnerability?
To exploit this vulnerability, an attacker would first have to log on to the system. An attacker could then run a specially crafted application that could exploit the vulnerability and take complete control over an affected system.

What systems are primarily at risk from the vulnerability?
Workstations and terminal servers are primarily at risk. Servers could be at more risk if administrators allow users to log on to servers and to run programs. However, best practices strongly discourage allowing this.

What does the update do?
The update addresses the vulnerability by ensuring that the Windows Kernel handles the exception properly.

When this security bulletin was issued, had this vulnerability been publicly disclosed?
Yes. This vulnerability has been publicly disclosed. It has been assigned Common Vulnerability and Exposure number CVE-2010-0232. This issue was first discussed in Microsoft Security Advisory 979682.

When this security bulletin was issued, had Microsoft received any reports that this vulnerability was being exploited?
No. Microsoft had not received any information to indicate that this vulnerability had been publicly used to attack customers when this security bulletin was originally issued.

Windows Kernel Double Free Vulnerability - CVE-2010-0233

An elevation of privilege vulnerability exists in the Windows Kernel due to a double free condition. An attacker who successfully exploited this vulnerability could run arbitrary code in kernel mode. An attacker could then install programs; view, change, or delete data; or create new accounts with full user rights.

To view this vulnerability as a standard entry in the Common Vulnerabilities and Exposures list, see CVE-2010-0233.

Mitigating Factors for Windows Kernel Double Free Vulnerability - CVE-2010-0233

Mitigation refers to a setting, common configuration, or general best-practice, existing in a default state, that could reduce the severity of exploitation of a vulnerability. The following mitigating factors may be helpful in your situation:

  • An attacker must have valid logon credentials and be able to log on locally to exploit this vulnerability. The vulnerability could not be exploited remotely or by anonymous users.

Workarounds for Windows Kernel Double Free Vulnerability - CVE-2010-0233

Microsoft has not identified any workarounds for this vulnerability.

FAQ for Windows Kernel Double Free Vulnerability - CVE-2010-0233

What is the scope of the vulnerability?
This is an elevation of privilege vulnerability. An attacker who successfully exploited this vulnerability could execute arbitrary code and take complete control of an affected system. An attacker could then install programs; view, change, or delete data; or create new accounts with full user rights.

What causes the vulnerability?
The Windows Kernel does not correctly reset a pointer when freeing memory. This results in a double free condition in the Windows Kernel.

What is the Windows Kernel?
The Windows Kernel is the core of the operating system. It provides system level services such as device management and memory management, allocates processor time to processes, and manages error handling.

What is a "double free" condition?
A double free condition is a condition in which a program is caused to release or free allocated memory more than once. Releasing memory that has already been freed could lead to memory corruption. An attacker could add arbitrary code to memory that is then executed when the corruption occurs. This code could then be executed at a system level of privilege.

Typically, this vulnerability will cause a denial of service to occur. However, in some circumstances, code execution could occur. Because of the unique layout of the memory on each affected system, exploiting this vulnerability on a mass scale could be difficult.

What might an attacker use the vulnerability to do?
An attacker who successfully exploited this vulnerability could run arbitrary code in kernel mode. An attacker could then install programs; view, change, or delete data; or create new accounts with full user rights.

How could an attacker exploit the vulnerability?
To exploit this vulnerability, an attacker would first have to log on to the system. An attacker could then run a specially crafted application that could exploit the vulnerability and take complete control over the affected system.

What systems are primarily at risk from the vulnerability?
Workstations and terminal servers are primarily at risk. Servers could be at more risk if administrators allow users to log on to servers and to run programs. However, best practices strongly discourage allowing this.

What does the update do?
The update addresses the vulnerability by ensuring that the Windows Kernel correctly resets pointers when freeing memory.

When this security bulletin was issued, had this vulnerability been publicly disclosed?
No. Microsoft received information about this vulnerability through responsible disclosure.

When this security bulletin was issued, had Microsoft received any reports that this vulnerability was being exploited?
No. Microsoft had not received any information to indicate that this vulnerability had been publicly used to attack customers when this security bulletin was originally issued.

Update Information

Detection and Deployment Tools and Guidance

Manage the software and security updates you need to deploy to the servers, desktop, and mobile systems in your organization. For more information see the TechNet Update Management Center. The Microsoft TechNet Security Web site provides additional information about security in Microsoft products.

Security updates are available from Microsoft Update and Windows Update. Security updates are also available from the Microsoft Download Center. You can find them most easily by doing a keyword search for "security update."

Finally, security updates can be downloaded from the Microsoft Update Catalog. The Microsoft Update Catalog provides a searchable catalog of content made available through Windows Update and Microsoft Update, including security updates, drivers and service packs. By searching using the security bulletin number (such as, "MS07-036"), you can add all of the applicable updates to your basket (including different languages for an update), and download to the folder of your choosing. For more information about the Microsoft Update Catalog, see the Microsoft Update Catalog FAQ.

Note Microsoft discontinued support for Office Update and the Office Update Inventory Tool as of August 1, 2009. To continue getting the latest updates for Microsoft Office products, use Microsoft Update. For more information, see About Microsoft Office Update: Frequently Asked Questions.

Detection and Deployment Guidance

Microsoft provides detection and deployment guidance for security updates. This guidance contains recommendations and information that can help IT professionals understand how to use various tools for detection and deployment of security updates. For more information, see Microsoft Knowledge Base Article 961747.

Microsoft Baseline Security Analyzer

Microsoft Baseline Security Analyzer (MBSA) allows administrators to scan local and remote systems for missing security updates as well as common security misconfigurations. For more information about MBSA, visit Microsoft Baseline Security Analyzer.

The following table provides the MBSA detection summary for this security update.

Software MBSA 2.1.1
Microsoft Windows 2000 Service Pack 4 Yes
Windows XP Service Pack 2 and Windows XP Service Pack 3 Yes
Windows XP Professional x64 Edition Service Pack 2 Yes
Windows Server 2003 Service Pack 2 Yes
Windows Server 2003 x64 Edition Service Pack 2 Yes
Windows Server 2003 with SP2 for Itanium-based Systems Yes
Windows Vista, Windows Vista Service Pack 1, and Windows Vista Service Pack 2 Yes
Windows Vista x64 Edition, Windows Vista x64 Edition Service Pack 1, and Windows Vista x64 Edition Service Pack 2 Yes
Windows Server 2008 for 32-bit Systems and Windows Server 2008 for 32-bit Systems Service Pack 2 Yes
Windows Server 2008 for x64-based Systems and Windows Server 2008 for x64-based Systems Service Pack 2 Yes
Windows Server 2008 for Itanium-based Systems and Windows Server 2008 for Itanium-based Systems Service Pack 2 Yes
Windows 7 for 32-bit Systems Yes

The latest version of MBSA has been released: Microsoft Baseline Security Analyzer 2.1.1. For more information, see Microsoft Baseline Security Analyzer 2.1.

Windows Server Update Services

By using Windows Server Update Services (WSUS), administrators can deploy the latest critical updates and security updates for Microsoft Windows 2000 operating systems and later, Office XP and later, Exchange Server 2003, and SQL Server 2000. For more information about how to deploy this security update using Windows Server Update Services, visit the Windows Server Update Services Web site.

Systems Management Server

The following table provides the SMS detection and deployment summary for this security update.

Software SMS 2.0 SMS 2003 with SUIT SMS 2003 with ITMU Configuration Manager 2007
Microsoft Windows 2000 Service Pack 4 Yes Yes Yes Yes
Windows XP Service Pack 2 and Windows XP Service Pack 3 Yes Yes Yes Yes
Windows XP Professional x64 Edition Service Pack 2 No No Yes Yes
Windows Server 2003 Service Pack 2 Yes Yes Yes Yes
Windows Server 2003 x64 Edition Service Pack 2 No No Yes Yes
Windows Server 2003 with SP2 for Itanium-based Systems No No Yes Yes
Windows Vista, Windows Vista Service Pack 1, and Windows Vista Service Pack 2 No No Yes Yes
Windows Vista x64 Edition, Windows Vista x64 Edition Service Pack 1, and Windows Vista x64 Edition Service Pack 2 No No Yes Yes
Windows Server 2008 for 32-bit Systems and Windows Server 2008 for 32-bit Systems Service Pack 2 No No Yes Yes
Windows Server 2008 for x64-based Systems and Windows Server 2008 for x64-based Systems Service Pack 2 No No Yes Yes
Windows Server 2008 for Itanium-based Systems and Windows Server 2008 for Itanium-based Systems Service Pack 2 No No Yes Yes
Windows 7 for 32-bit Systems No No Yes Yes

For SMS 2.0 and SMS 2003, the Security Update Inventory Tool (SUIT) can be used by SMS to detect security updates. See also Downloads for Systems Management Server 2.0.

For SMS 2003, the SMS 2003 Inventory Tool for Microsoft Updates (ITMU) can be used by SMS to detect security updates that are offered by Microsoft Update and that are supported by Windows Server Update Services. For more information about the SMS 2003 ITMU, see SMS 2003 Inventory Tool for Microsoft Updates. For more information about SMS scanning tools, see SMS 2003 Software Update Scanning Tools. See also Downloads for Systems Management Server 2003.

System Center Configuration Manager 2007 uses WSUS 3.0 for detection of updates. For more information about Configuration Manager 2007 Software Update Management, visit System Center Configuration Manager 2007.

For more information about SMS, visit the SMS Web site.

For more detailed information, see Microsoft Knowledge Base Article 910723: Summary list of monthly detection and deployment guidance articles.

Update Compatibility Evaluator and Application Compatibility Toolkit

Updates often write to the same files and registry settings required for your applications to run. This can trigger incompatibilities and increase the time it takes to deploy security updates. You can streamline testing and validating Windows updates against installed applications with the Update Compatibility Evaluator components included with Application Compatibility Toolkit.

The Application Compatibility Toolkit (ACT) contains the necessary tools and documentation to evaluate and mitigate application compatibility issues before deploying Microsoft Windows Vista, a Windows Update, a Microsoft Security Update, or a new version of Windows Internet Explorer in your environment.

Security Update Deployment

Affected Software

For information about the specific security update for your affected software, click the appropriate link:

Windows 2000 (all editions)

Reference Table

The following table contains the security update information for this software. You can find additional information in the subsection, Deployment Information, in this section.

Inclusion in Future Service Packs The update for this issue may be included in a future update rollup
Deployment
Installing without user intervention Windows2000-KB977165-x86-enu /quiet
Installing without restarting Windows2000-KB977165-x86-enu /norestart
Update log file KB977165.log
Further information See the subsection, Detection and Deployment Tools and Guidance
Restart Requirement
Restart required? Yes, you must restart your system after you apply this security update.
HotPatching Not applicable
Removal Information Use Add or Remove Programs tool in Control Panel or the Spuninst.exe utility located in the %Windir%$NTUninstallKB977165$\Spuninst folder
File Information See Microsoft Knowledge Base Article 977165
Registry Key Verification For the package released February 9, 2010:\ HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Updates\Windows 2000\SP5\KB977165\Filelist\ For the revised package released March 2, 2010:\ HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Updates\Windows 2000\SP5\KB977165-v2\Filelist

Deployment Information

Installing the Update

When you install this security update, the installer checks whether one or more of the files that are being updated on your system have previously been updated by a Microsoft hotfix.

If you have previously installed a hotfix to update one of these files, the installer copies the RTMQFE, SP1QFE, or SP2QFE files to your system. Otherwise, the installer copies the RTMGDR, SP1GDR, or SP2GDR files to your system. Security updates may not contain all variations of these files. For more information about this behavior, see Microsoft Knowledge Base Article 824994.

For more information about the installer, visit the Microsoft TechNet Web site.

For more information about the terminology that appears in this bulletin, such as hotfix, see Microsoft Knowledge Base Article 824684.

This security update supports the following setup switches.

Switch Description
/help Displays the command-line options.
Setup Modes
/passive Unattended Setup mode. No user interaction is required, but installation status is displayed. If a restart is required at the end of Setup, a dialog box will be presented to the user with a timer warning that the computer will restart in 30 seconds.
/quiet Quiet mode. This is the same as unattended mode, but no status or error messages are displayed.
Restart Options
/norestart Does not restart when installation has completed.
/forcerestart Restarts the computer after installation and force other applications to close at shutdown without saving open files first.
/warnrestart[:x] Presents a dialog box with a timer warning the user that the computer will restart in x seconds. (The default setting is 30 seconds.) Intended for use with the /quiet switch or the /passive switch.
/promptrestart Displays a dialog box prompting the local user to allow a restart.
Special Options
/overwriteoem Overwrites OEM files without prompting.
/nobackup Does not back up files needed for uninstall.
/forceappsclose Forces other programs to close when the computer shuts down.
/log:path Allows the redirection of installation log files.
/extract[:path] Extracts files without starting the Setup program.
/ER Enables extended error reporting.
/verbose Enables verbose logging. During installation, creates %Windir%\CabBuild.log. This log details the files that are copied. Using this switch may cause the installation to proceed more slowly.

Note You can combine these switches into one command. For backward compatibility, the security update also supports the setup switches that the earlier version of the Setup program uses. For more information about the supported installation switches, see Microsoft Knowledge Base Article 262841.

Removing the Update

This security update supports the following setup switches.

Switch Description
/help Displays the command-line options.
Setup Modes
/passive Unattended Setup mode. No user interaction is required, but installation status is displayed. If a restart is required at the end of Setup, a dialog box will be presented to the user with a timer warning that the computer will restart in 30 seconds.
/quiet Quiet mode. This is the same as unattended mode, but no status or error messages are displayed.
Restart Options
/norestart Does not restart when installation has completed.
/forcerestart Restarts the computer after installation and force other applications to close at shutdown without saving open files first.
/warnrestart[:x] Presents a dialog box with a timer warning the user that the computer will restart in x seconds. (The default setting is 30 seconds.) Intended for use with the /quiet switch or the /passive switch.
/promptrestart Displays a dialog box prompting the local user to allow a restart.
Special Options
/forceappsclose Forces other programs to close when the computer shuts down.
/log:path Allows the redirection of installation log files.

Verifying That the Update Has Been Applied

  • Microsoft Baseline Security Analyzer
    To verify that a security update has been applied to an affected system, you may be able to use the Microsoft Baseline Security Analyzer (MBSA) tool. See the section, Detection and Deployment Tools and Guidance, earlier in this bulletin for more information.

  • File Version Verification
    Because there are several editions of Microsoft Windows, the following steps may be different on your system. If they are, see your product documentation to complete these steps.

    1. Click Start, and then click Search.
    2. In the Search Results pane, click All files and folders under Search Companion.
    3. In the All or part of the file name box, type a file name from the appropriate file information table, and then click Search.
    4. In the list of files, right-click a file name from the appropriate file information table, and then click Properties.
      Note Depending on the edition of the operating system, or the programs that are installed on your system, some of the files that are listed in the file information table may not be installed.
    5. On the Version tab, determine the version of the file that is installed on your system by comparing it to the version that is documented in the appropriate file information table.
      Note Attributes other than the file version may change during installation. Comparing other file attributes to the information in the file information table is not a supported method of verifying that the update has been applied. Also, in certain cases, files may be renamed during installation. If the file or version information is not present, use one of the other available methods to verify update installation.
  • Registry Key Verification
    You may also be able to verify the files that this security update has installed by reviewing the registry keys listed in the Reference Table in this section.

    These registry keys may not contain a complete list of installed files. Also, these registry keys may not be created correctly when an administrator or an OEM integrates or slipstreams this security update into the Windows installation source files.

Windows XP (all editions)

Reference Table

The following table contains the security update information for this software. You can find additional information in the subsection, Deployment Information, in this section.

Inclusion in Future Service Packs The update for this issue will be included in a future service pack or update rollup
Deployment
Installing without user intervention For Windows XP Service Pack 2 and Windows XP Service Pack 3:\ WindowsXP-KB977165-x86-enu /quiet
For Windows XP Professional x64 Edition Service Pack 2:\ WindowsServer2003.WindowsXP-KB977165-x64-enu /quiet
Installing without restarting For Windows XP Service Pack 2 and Windows XP Service Pack 3:\ WindowsXP-KB977165-x86-enu /norestart
For Windows XP Professional x64 Edition Service Pack 2:\ WindowsServer2003.WindowsXP-KB977165-x64-enu /norestart
Update log file KB977165.log
Further information See the subsection, Detection and Deployment Tools and Guidance
Restart Requirement
Restart required? Yes, you must restart your system after you apply this security update.
HotPatching Not applicable
Removal Information Use Add or Remove Programs tool in Control Panel or the Spuninst.exe utility located in the %Windir%$NTUninstallKB977165 $\Spuninst folder
File Information See Microsoft Knowledge Base Article 977165
Registry Key Verification For all supported 32-bit editions of Windows XP, using the package released February 9, 2010:\ HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Updates\Windows XP\SP4\KB977165\Filelist\ For all supported 32-bit editions of Windows XP, using the revised package released March 2, 2010:\ HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Updates\Windows XP\SP4\KB977165-v2\Filelist
For all supported x64-based editions of Windows XP:\ HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Updates\Windows XP Version 2003\SP3\KB977165\Filelist

Note For supported versions of Windows XP Professional x64 Edition, this security update is the same as supported versions of the Windows Server 2003 x64 Edition security update.

Deployment Information

Installing the Update

When you install this security update, the installer checks whether one or more of the files that are being updated on your system have previously been updated by a Microsoft hotfix.

If you have previously installed a hotfix to update one of these files, the installer copies the RTMQFE, SP1QFE, or SP2QFE files to your system. Otherwise, the installer copies the RTMGDR, SP1GDR, or SP2GDR files to your system. Security updates may not contain all variations of these files. For more information about this behavior, see Microsoft Knowledge Base Article 824994.

For more information about the installer, visit the Microsoft TechNet Web site.

For more information about the terminology that appears in this bulletin, such as hotfix, see Microsoft Knowledge Base Article 824684.

This security update supports the following setup switches.

Switch Description
/help Displays the command-line options.
Setup Modes
/passive Unattended Setup mode. No user interaction is required, but installation status is displayed. If a restart is required at the end of Setup, a dialog box will be presented to the user with a timer warning that the computer will restart in 30 seconds.
/quiet Quiet mode. This is the same as unattended mode, but no status or error messages are displayed.
Restart Options
/norestart Does not restart when installation has completed.
/forcerestart Restarts the computer after installation and force other applications to close at shutdown without saving open files first.
/warnrestart[:x] Presents a dialog box with a timer warning the user that the computer will restart in x seconds. (The default setting is 30 seconds.) Intended for use with the /quiet switch or the /passive switch.
/promptrestart Displays a dialog box prompting the local user to allow a restart.
Special Options
/overwriteoem Overwrites OEM files without prompting.
/nobackup Does not back up files needed for uninstall.
/forceappsclose Forces other programs to close when the computer shuts down.
/log:path Allows the redirection of installation log files.
/integrate:path Integrates the update into the Windows source files. These files are located at the path that is specified in the switch.
/extract[:path] Extracts files without starting the Setup program.
/ER Enables extended error reporting.
/verbose Enables verbose logging. During installation, creates %Windir%\CabBuild.log. This log details the files that are copied. Using this switch may cause the installation to proceed more slowly.

Note You can combine these switches into one command. For backward compatibility, the security update also supports the setup switches that the earlier version of the Setup program uses. For more information about the supported installation switches, see Microsoft Knowledge Base Article 262841.

Removing the Update

This security update supports the following setup switches.

Switch Description
/help Displays the command-line options.
Setup Modes
/passive Unattended Setup mode. No user interaction is required, but installation status is displayed. If a restart is required at the end of Setup, a dialog box will be presented to the user with a timer warning that the computer will restart in 30 seconds.
/quiet Quiet mode. This is the same as unattended mode, but no status or error messages are displayed.
Restart Options
/norestart Does not restart when installation has completed
/forcerestart Restarts the computer after installation and force other applications to close at shutdown without saving open files first.
/warnrestart[:x] Presents a dialog box with a timer warning the user that the computer will restart in x seconds. (The default setting is 30 seconds.) Intended for use with the /quiet switch or the /passive switch.
/promptrestart Displays a dialog box prompting the local user to allow a restart.
Special Options
/forceappsclose Forces other programs to close when the computer shuts down.
/log:path Allows the redirection of installation log files.

Verifying That the Update Has Been Applied

  • Microsoft Baseline Security Analyzer
    To verify that a security update has been applied to an affected system, you may be able to use the Microsoft Baseline Security Analyzer (MBSA) tool. See the section, Detection and Deployment Tools and Guidance, earlier in this bulletin for more information.

  • File Version Verification
    Because there are several editions of Microsoft Windows, the following steps may be different on your system. If they are, see your product documentation to complete these steps.

    1. Click Start, and then click Search.
    2. In the Search Results pane, click All files and folders under Search Companion.
    3. In the All or part of the file name box, type a file name from the appropriate file information table, and then click Search.
    4. In the list of files, right-click a file name from the appropriate file information table, and then click Properties.
      Note Depending on the edition of the operating system, or the programs that are installed on your system, some of the files that are listed in the file information table may not be installed.
    5. On the Version tab, determine the version of the file that is installed on your system by comparing it to the version that is documented in the appropriate file information table.
      Note Attributes other than the file version may change during installation. Comparing other file attributes to the information in the file information table is not a supported method of verifying that the update has been applied. Also, in certain cases, files may be renamed during installation. If the file or version information is not present, use one of the other available methods to verify update installation.
  • Registry Key Verification
    You may also be able to verify the files that this security update has installed by reviewing the registry keys listed in the Reference Table in this section.

    These registry keys may not contain a complete list of installed files. Also, these registry keys may not be created correctly when an administrator or an OEM integrates or slipstreams this security update into the Windows installation source files.

Windows Server 2003 (all editions)

Reference Table

The following table contains the security update information for this software. You can find additional information in the subsection, Deployment Information, in this section.

Inclusion in Future Service Packs The update for this issue will be included in a future service pack or update rollup
Deployment
Installing without user intervention For all supported 32-bit editions of Windows Server 2003:\ WindowsServer2003-KB977165-x86-enu /quiet
For all supported x64-based editions of Windows Server 2003:\ WindowsServer2003.WindowsXP-KB977165-x64-enu /quiet
For all supported Itanium-based editions of Windows Server 2003:\ WindowsServer2003-KB977165-ia64-enu /quiet
Installing without restarting For all supported 32-bit editions of Windows Server 2003:\ WindowsServer2003-KB977165-x86-enu /norestart
For all supported x64-based editions of Windows Server 2003:\ WindowsServer2003.WindowsXP-KB977165-x64-enu /norestart
For all supported Itanium-based editions of Windows Server 2003:\ WindowsServer2003-KB977165-ia64-enu /norestart
Update log file KB977165.log
Further information See the subsection, Detection and Deployment Tools and Guidance
Restart Requirement
Restart required? Yes, you must restart your system after you apply this security update.
HotPatching This security update does not support HotPatching. For more information about HotPatching, see Microsoft Knowledge Base Article 897341.
Removal Information Use Add or Remove Programs tool in Control Panel or the Spuninst.exe utility located in the %Windir%$NTUninstallKB977165$\Spuninst folder
File Information See Microsoft Knowledge Base Article 977165
Registry Key Verification For all supported 32-bit editions of Windows Server 2003, using the package released February 9, 2010:\ HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Updates\Windows Server 2003\SP3\KB977165\Filelist\ For all supported 32-bit editions of Windows Server 2003, using the revised package released March 2, 2010:\ HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Updates\Windows Server 2003\SP3\KB977165-v2\Filelist
For all supported x-64 based and Itanium-based editions of Windows Server 2003, using the packages released February 9, 2010:\ HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Updates\Windows Server 2003\SP3\KB977165\Filelist

Deployment Information

Installing the Update

When you install this security update, the installer checks to see if one or more of the files that are being updated on your system have previously been updated by a Microsoft hotfix.

If you have previously installed a hotfix to update one of these files, the installer copies the RTMQFE, SP1QFE, or SP2QFE files to your system. Otherwise, the installer copies the RTMGDR, SP1GDR, or SP2GDR files to your system. Security updates may not contain all variations of these files. For more information about this behavior, see Microsoft Knowledge Base Article 824994.

For more information about the installer, visit the Microsoft TechNet Web site.

For more information about the terminology that appears in this bulletin, such as hotfix, see Microsoft Knowledge Base Article 824684.

This security update supports the following setup switches.

Switch Description
/help Displays the command-line options.
Setup Modes
/passive Unattended Setup mode. No user interaction is required, but installation status is displayed. If a restart is required at the end of Setup, a dialog box will be presented to the user with a timer warning that the computer will restart in 30 seconds.
/quiet Quiet mode. This is the same as unattended mode, but no status or error messages are displayed.
Restart Options
/norestart Does not restart when installation has completed.
/forcerestart Restarts the computer after installation and force other applications to close at shutdown without saving open files first.
/warnrestart[:x] Presents a dialog box with a timer warning the user that the computer will restart in x seconds. (The default setting is 30 seconds.) Intended for use with the /quiet switch or the /passive switch.
/promptrestart Displays a dialog box prompting the local user to allow a restart.
Special Options
/overwriteoem Overwrites OEM files without prompting.
/nobackup Does not back up files needed for uninstall.
/forceappsclose Forces other programs to close when the computer shuts down.
/log:path Allows the redirection of installation log files.
/integrate:path Integrates the update into the Windows source files. These files are located at the path that is specified in the switch.
/extract[:path] Extracts files without starting the Setup program.
/ER Enables extended error reporting.
/verbose Enables verbose logging. During installation, creates %Windir%\CabBuild.log. This log details the files that are copied. Using this switch may cause the installation to proceed more slowly.

Note You can combine these switches into one command. For backward compatibility, the security update also supports many of the setup switches that the earlier version of the Setup program uses. For more information about the supported installation switches, see Microsoft Knowledge Base Article 262841.

Removing the Update

This security update supports the following setup switches.

Switch Description
/help Displays the command-line options.
Setup Modes
/passive Unattended Setup mode. No user interaction is required, but installation status is displayed. If a restart is required at the end of Setup, a dialog box will be presented to the user with a timer warning that the computer will restart in 30 seconds.
/quiet Quiet mode. This is the same as unattended mode, but no status or error messages are displayed.
Restart Options
/norestart Does not restart when installation has completed.
/forcerestart Restarts the computer after installation and force other applications to close at shutdown without saving open files first.
/warnrestart[:x] Presents a dialog box with a timer warning the user that the computer will restart in x seconds. (The default setting is 30 seconds.) Intended for use with the /quiet switch or the /passive switch.
/promptrestart Displays a dialog box prompting the local user to allow a restart.
Special Options
/forceappsclose Forces other programs to close when the computer shuts down.
/log:path Allows the redirection of installation log files.

Verifying that the Update Has Been Applied

  • Microsoft Baseline Security Analyzer
    To verify that a security update has been applied to an affected system, you may be able to use the Microsoft Baseline Security Analyzer (MBSA) tool. See the section, Detection and Deployment Tools and Guidance, earlier in this bulletin for more information.

  • File Version Verification
    Because there are several editions of Microsoft Windows, the following steps may be different on your system. If they are, see your product documentation to complete these steps.

    1. Click Start, and then click Search.
    2. In the Search Results pane, click All files and folders under Search Companion.
    3. In the All or part of the file name box, type a file name from the appropriate file information table, and then click Search.
    4. In the list of files, right-click a file name from the appropriate file information table, and then click Properties.
      Note Depending on the edition of the operating system, or the programs that are installed on your system, some of the files that are listed in the file information table may not be installed.
    5. On the Version tab, determine the version of the file that is installed on your system by comparing it to the version that is documented in the appropriate file information table.
      Note Attributes other than the file version may change during installation. Comparing other file attributes to the information in the file information table is not a supported method of verifying that the update has been applied. Also, in certain cases, files may be renamed during installation. If the file or version information is not present, use one of the other available methods to verify update installation.
  • Registry Key Verification
    You may also be able to verify the files that this security update has installed by reviewing the registry keys listed in the Reference Table in this section.

    These registry keys may not contain a complete list of installed files. Also, these registry keys may not be created correctly when an administrator or an OEM integrates or slipstreams this security update into the Windows installation source files.

Windows Vista (all editions)

Reference Table

The following table contains the security update information for this software. You can find additional information in the subsection, Deployment Information, in this section.

Inclusion in Future Service Packs The update for this issue will be included in a future service pack or update rollup
Deployment
Installing without user intervention For all supported 32-bit editions of Windows Vista:\ Windows6.0-KB977165-x86 /quiet
For all supported x64-based editions of Windows Vista:\ Windows6.0-KB977165-x64 /quiet
Installing without restarting For all supported 32-bit editions of Windows Vista:\ Windows6.0-KB977165-x86 /quiet /norestart
For all supported x64-based editions of Windows Vista:\ Windows6.0-KB977165-x64 /quiet /norestart
Further information See the subsection, Detection and Deployment Tools and Guidance
Restart Requirement
Restart required? Yes, you must restart your system after you apply this security update.
HotPatching Not applicable.
Removal Information WUSA.exe does not support uninstall of updates. To uninstall an update installed by WUSA, click Control Panel, and then click Security. Under Windows Update, click View installed updates and select from the list of updates.
File Information See Microsoft Knowledge Base Article 977165
Registry Key Verification Note A registry key does not exist to validate the presence of this update.

Deployment Information

Installing the Update

When you install this security update, the installer checks whether one or more of the files that are being updated on your system have previously been updated by a Microsoft hotfix.

For more information about the terminology that appears in this bulletin, such as hotfix, see Microsoft Knowledge Base Article 824684.

This security update supports the following setup switches.

Switch Description
/?, /h, /help Displays help on supported switches.
/quiet Suppresses the display of status or error messages.
/norestart When combined with /quiet, the system will not be restarted after installation even if a restart is required to complete installation.

Note For more information about the wusa.exe installer, see Microsoft Knowledge Base Article 934307.

Verifying That the Update Has Been Applied

  • Microsoft Baseline Security Analyzer
    To verify that a security update has been applied to an affected system, you may be able to use the Microsoft Baseline Security Analyzer (MBSA) tool. See the section, Detection and Deployment Tools and Guidance, earlier in this bulletin for more information.

  • File Version Verification
    Because there are several editions of Microsoft Windows, the following steps may be different on your system. If they are, see your product documentation to complete these steps.

    1. Click Start and then enter an update file name in Start Search.
    2. When the file appears under Programs, right-click on the file name and click Properties.
    3. Under the General tab, compare the file size with the file information tables provided in the bulletin KB article.
    4. You may also click on the Details tab and compare information, such as file version and date modified, with the file information tables provided in the bulletin KB article.
    5. Finally, you may also click on the Previous Versions tab and compare file information for the previous version of the file with the file information for the new, or updated, version of the file.

Windows Server 2008 (all editions)

Reference Table

The following table contains the security update information for this software. You can find additional information in the subsection, Deployment Information, in this section.

Inclusion in Future Service Packs The update for this issue will be included in a future service pack or update rollup
Deployment
Installing without user intervention For all supported 32-bit editions of Windows Server 2008:\ Windows6.0-KB977165-x86 /quiet
For all supported x64-based editions of Windows Server 2008:\ Windows6.0-KB977165-x64 /quiet
For all supported Itanium-based editions of Windows Server 2008:\ Windows6.0-KB977165-ia64 /quiet
Installing without restarting For all supported 32-bit editions of Windows Server 2008:\ Windows6.0-KB977165-x86 /quiet /norestart
For all supported x64-based editions of Windows Server 2008:\ Windows6.0-KB977165-x64 /quiet /norestart
For all supported Itanium-based editions of Windows Server 2008:\ Windows6.0-KB977165-ia64 /quiet /norestart
Further information See the subsection, Detection and Deployment Tools and Guidance
Restart Requirement
Restart required? Yes, you must restart your system after you apply this security update.
HotPatching Not applicable.
Removal Information WUSA.exe does not support uninstall of updates. To uninstall an update installed by WUSA, click Control Panel, and then click Security. Under Windows Update, click View installed updates and select from the list of updates.
File Information See Microsoft Knowledge Base Article 977165
Registry Key Verification Note A registry key does not exist to validate the presence of this update.

Deployment Information

Installing the Update

When you install this security update, the installer checks whether one or more of the files that are being updated on your system have previously been updated by a Microsoft hotfix.

For more information about the terminology that appears in this bulletin, such as hotfix, see Microsoft Knowledge Base Article 824684.

This security update supports the following setup switches.

Switch Description
/?, /h, /help Displays help on supported switches.
/quiet Suppresses the display of status or error messages.
/norestart When combined with /quiet, the system will not be restarted after installation even if a restart is required to complete installation.

Note For more information about the wusa.exe installer, see Microsoft Knowledge Base Article 934307.

Verifying That the Update Has Been Applied

  • Microsoft Baseline Security Analyzer
    To verify that a security update has been applied to an affected system, you may be able to use the Microsoft Baseline Security Analyzer (MBSA) tool. See the section, Detection and Deployment Tools and Guidance, earlier in this bulletin for more information.

  • File Version Verification
    Because there are several editions of Microsoft Windows, the following steps may be different on your system. If they are, see your product documentation to complete these steps.

    1. Click Start and then enter an update file name in Start Search.
    2. When the file appears under Programs, right-click on the file name and click Properties.
    3. Under the General tab, compare the file size with the file information tables provided in the bulletin KB article.
    4. You may also click on the Details tab and compare information, such as file version and date modified, with the file information tables provided in the bulletin KB article.
    5. Finally, you may also click on the Previous Versions tab and compare file information for the previous version of the file with the file information for the new, or updated, version of the file.

Windows 7

Reference Table

The following table contains the security update information for this software. You can find additional information in the subsection, Deployment Information, in this section.

Inclusion in Future Service Packs The update for this issue will be included in a future service pack or update rollup
Deployment
Installing without user intervention For all supported 32-bit editions of Windows 7:\ Windows6.1-KB977165-x86 /quiet
Installing without restarting For all supported 32-bit editions of Windows 7:\ Windows6.1-KB977165-x86 /quiet /norestart
Further information See the subsection, Detection and Deployment Tools and Guidance
Restart Requirement
Restart required? Yes, you must restart your system after you apply this security update.
HotPatching Not applicable.
Removal Information WUSA.exe does not support uninstall of updates. To uninstall an update installed by WUSA, click Control Panel, and then click Security. Under Windows Update, click View installed updates and select from the list of updates.
File Information See Microsoft Knowledge Base Article 977165
Registry Key Verification Note A registry key does not exist to validate the presence of this update.

Deployment Information

Installing the Update

When you install this security update, the installer checks whether one or more of the files that are being updated on your system have previously been updated by a Microsoft hotfix.

For more information about the terminology that appears in this bulletin, such as hotfix, see Microsoft Knowledge Base Article 824684.

This security update supports the following setup switches.

Switch Description
/?, /h, /help Displays help on supported switches.
/quiet Suppresses the display of status or error messages.
/norestart When combined with /quiet, the system will not be restarted after installation even if a restart is required to complete installation.

Note For more information about the wusa.exe installer, see Microsoft Knowledge Base Article 934307.

Verifying That the Update Has Been Applied

  • Microsoft Baseline Security Analyzer
    To verify that a security update has been applied to an affected system, you may be able to use the Microsoft Baseline Security Analyzer (MBSA) tool. See the section, Detection and Deployment Tools and Guidance, earlier in this bulletin for more information.

  • File Version Verification
    Because there are several editions of Microsoft Windows, the following steps may be different on your system. If they are, see your product documentation to complete these steps.

    1. Click Start and then enter an update file name in Start Search.
    2. When the file appears under Programs, right-click on the file name and click Properties.
    3. Under the General tab, compare the file size with the file information tables provided in the bulletin KB article.
    4. You may also click on the Details tab and compare information, such as file version and date modified, with the file information tables provided in the bulletin KB article.
    5. Finally, you may also click on the Previous Versions tab and compare file information for the previous version of the file with the file information for the new, or updated, version of the file.

Other Information

Acknowledgments

Microsoft thanks the following for working with us to help protect customers:

  • Tavis Ormandy of Google Inc. for reporting the Windows Kernel Double Free Vulnerability (CVE-2010-0233)

Microsoft Active Protections Program (MAPP)

To improve security protections for customers, Microsoft provides vulnerability information to major security software providers in advance of each monthly security update release. Security software providers can then use this vulnerability information to provide updated protections to customers via their security software or devices, such as antivirus, network-based intrusion detection systems, or host-based intrusion prevention systems. To determine whether active protections are available from security software providers, please visit the active protections Web sites provided by program partners, listed in Microsoft Active Protections Program (MAPP) Partners.

Support

  • Customers in the U.S. and Canada can receive technical support from Security Support or 1-866-PCSAFETY. There is no charge for support calls that are associated with security updates. For more information about available support options, see Microsoft Help and Support.
  • International customers can receive support from their local Microsoft subsidiaries. There is no charge for support that is associated with security updates. For more information about how to contact Microsoft for support issues, visit the International Support Web site.

Disclaimer

The information provided in the Microsoft Knowledge Base is provided "as is" without warranty of any kind. Microsoft disclaims all warranties, either express or implied, including the warranties of merchantability and fitness for a particular purpose. In no event shall Microsoft Corporation or its suppliers be liable for any damages whatsoever including direct, indirect, incidental, consequential, loss of business profits or special damages, even if Microsoft Corporation or its suppliers have been advised of the possibility of such damages. Some states do not allow the exclusion or limitation of liability for consequential or incidental damages so the foregoing limitation may not apply.

Revisions

  • V1.0 (February 9, 2010): Bulletin published.
  • V1.1 (February 10, 2010): Corrected the verification registry key for all supported x64-based editions of Windows XP. This is an informational change only.
  • V1.2 (March 2, 2010): Added an item to the Frequently Asked Questions (FAQ) About this Security Update to announce the offering of revised packages on Windows Update. Customers who have already successfully updated their systems do not need to take any action.
  • V1.3 (March 17, 2010): Added verification registry keys for the revised packages released March 2, 2010 for Microsoft Windows 2000, Windows XP, and Windows Server 2003. This is an informational change only.

Built at 2014-04-18T13:49:36Z-07:00