Network Adapter Teaming Technical Preview
Published: February 29, 2012
Updated: February 29, 2012
Applies To: Windows Server 8 Beta
Network adapter teaming, also known as load balancing and failover (LBFO), allows multiple network adapters on a computer to be placed into a team for the following purposes:
Traffic failover to prevent connectivity loss in the event of a network component failure
This feature has been a requirement for independent hardware vendors (IHVs) to enter the server network adapter market, but until now network adapter teaming has not been included in Windows Server operating systems.
Network adapter teaming requires the presence of a single Ethernet network adapter, which can be used for separating traffic that is using VLANs. All modes that provide fault protection through failover require at least two Ethernet network adapters. Windows Server “8” Beta supports up to 32 network adapters in a team.
Network adapter teaming technology includes many parts and options of network adapter teaming technology. This guide includes the following sections:
Network adapter teaming architecture
Bandwidth aggregation (also known as load balancing) mechanisms
Traffic distribution algorithms
Network adapter teaming in virtual machines
Today, all network adapter teaming solutions on the market have a similar architecture, as shown in Figure 1.
Figure 1 Teaming solution architecture
Two or more physical network adapters are connected to the network adapter teaming solution multiplexing unit, which then presents one or more virtual adapters (also known as team network adapters) to the operating system. There are several different algorithms that distribute inbound and outbound traffic between the physical network adapters. In current non-Microsoft network adapter teaming solutions, the team network adapters divide traffic by virtual LAN (VLAN) so that applications can connect to different VLANs at the same time. Technically, this separation of traffic is not part of network adapter teaming. However, because other commercial implementations of network adapter teaming have this capability, the Windows Server “8” Beta implementation also includes it.
There are two basic sets of algorithms that are used for network adapter teaming:
Algorithms that require the switch to participate in the teaming, also known as switch-dependent modes. These algorithms usually require all the network adapters of the team to be connected to the same switch.
Algorithms that do not require the switch to participate in the teaming, also referred to as switch-independent modes. Because the switch does not know that the network adapter is part of a team, the team network adapters can be connected to different switches. Switch-independent modes do not require that the team members connect to different switches, they merely make it possible.
There are two common choices for switch-dependent modes of network adapter teaming:
- Generic or static teaming (IEEE 802.3ad draft v1). This mode requires configuration on the switch and the computer to identify which links form the team. Because this is a statically configured solution, no additional protocol assists the switch and the computer to identify incorrectly plugged cables or other errors that could cause the team to fail. This mode is typically supported by server-class switches.
- Dynamic teaming (IEEE 802.1ax, LACP). IEEE 802.1ax uses the Link Aggregation Control Protocol (LACP) to dynamically identify links between the computer and a specific switch. This enables the automatic creation of a team and, in theory, the expansion and reduction of a team simply by the transmission or receipt of LACP from the peer network adapter. Typical server-class switches support IEEE 802.1ax, but most switches require manual administration to enable LACP on the port.
Note IEEE 802.1ax is also commonly known as IEEE 802.3ad because it was developed by the IEEE 802.3ad committee before being published as IEEE 802.1ax.
Both modes should result in inbound and outbound traffic approaching the practical limits of the aggregated bandwidth because the pool of links in the team functions as a single pipeline.
Outbound traffic can be distributed among the available links in many ways. Try to keep all packets that are associated with a single flow (TCP stream) on a single network adapter. This is needed to minimize out-of-order packet arrival scenarios.
Network adapter teaming in Windows Server “8” Beta supports the following traffic distribution methods:
- Hyper-V switch port. In cases where virtual machines have independent media access control (MAC) addresses, the MAC address of the virtual machine can provide the basis for dividing traffic. There is an advantage in using this scheme in virtualization. Because the adjacent switch can determine that specific source MAC addresses are on only one connected network adapter, the switch will balance the egress load (the traffic from the switch to the computer) on multiple links, based on the destination MAC address for the virtual machine. This is particularly helpful when used with virtual machine queue. However, this mode might not be specific enough to get a well-balanced distribution, and it limits a single virtual machine to the bandwidth that is available on a single network adapter.
Note Windows Server “8” Beta uses the Hyper-V switch port as the identifier rather than the source MAC address, because in some instances, a virtual machine might be using more than one MAC address on a switch port.
- Hashing. This algorithm creates a hash based on components of the packet, and then it assigns packets that have that hash value to one of the available network adapters. This keeps all packets from the same TCP stream on the same network adapter. Hashing alone usually creates balance across the available network adapters. Some network adapter teaming solutions that are available on the market monitor the distribution of the traffic, and they reassign specific hash values to different network adapters in an attempt to better balance the traffic. The dynamic redistribution is known as smart load balancing or adaptive load balancing.
The components that can be used as inputs to the hashing function include the following:
Source and destination MAC addresses
Source and destination IP addresses, with or without considering the MAC addresses (double hash)
Source and destination TCP ports, usually used along with the IP addresses (quadruple hash)
The quadruple hash creates a finer distribution of traffic streams, which results in smaller streams that can be independently moved between network adapters. However, it cannot be used for traffic that is not TCP or UDP traffic or where the TCP and UDP ports are hidden from the stack, such as traffic that is protected by Internet Protocol security (IPsec). In these cases, the hash falls back to a double hash.
Network adapter teaming in Windows Server “8” Beta also works within a virtual machine. This allows a virtual machine to have virtual network adapters that are connected to more than one Hyper-V switch and still have connectivity even if the network adapter under that switch gets disconnected. This is particularly important when working with features such as Single Root I/O Virtualization (SR-IOV) because SR-IOV traffic does not go through the Hyper-V switch. Thus, it cannot be protected by a team that is under a Hyper-V switch. With the virtual machine teaming option, an administrator can set up two Hyper-V switches, each connected to its own SR-IOV-capable network adapter. At that point:
Each virtual machine can then install a virtual function from one or both SR-IOV network adapters. Then, in the event of a network adapter disconnect, the virtual machine can fail over from the primary virtual function to the backup virtual function.
Alternately, the virtual machine might have a virtual function from one network adapter and a non-virtual function network adapter to the other switch. If the network adapter that is associated with the virtual function gets disconnected, the traffic can fail over to the other switch without loss of connectivity.
|Because failover between network adapters in a virtual machine might result in traffic being sent with the MAC address of the other network adapter, each Hyper-V switch port that is associated with a virtual machine that is using network adapter teaming must be set to allow MAC spoofing.|
Network adapter teaming is compatible with all networking capabilities in Windows Server “8” Beta with three exceptions: SR-IOV, remote direct memory access (RDMA), and TCP Chimney. For SR-IOV and remote direct memory access (RDMA), data is delivered directly to the network adapter without passing through the networking stack. Therefore, it is not possible for the network adapter team to look at or redirect the data to another path in the team. TCP Chimney is not supported with network adapter teaming in Windows Server “8” Beta.
Contribuições da comunidade