Set-NetIsatapConfiguration

Set-NetIsatapConfiguration

Sets an ISATAP configuration on a computer or on a Group Policy Object (GPO).

Syntax

Parameter Set: ByName
Set-NetIsatapConfiguration [[-State] <State> ] [[-Router] <String> ] [[-ResolutionState] <State> ] [[-ResolutionIntervalSeconds] <UInt32> ] [-AsJob] [-CimSession <CimSession[]> ] [-GPOSession <String> ] [-IPInterface <CimInstance> ] [-PassThru] [-PolicyStore <String> ] [-ThrottleLimit <Int32> ] [-Confirm] [-WhatIf] [ <CommonParameters>]

Parameter Set: InputObject (cdxml)
Set-NetIsatapConfiguration [[-State] <State> ] [[-Router] <String> ] [[-ResolutionState] <State> ] [[-ResolutionIntervalSeconds] <UInt32> ] -InputObject <CimInstance[]> [-AsJob] [-CimSession <CimSession[]> ] [-PassThru] [-ThrottleLimit <Int32> ] [-Confirm] [-WhatIf] [ <CommonParameters>]

Detailed Description

The Set-NetIsatapConfiguration cmdlet sets an ISATAP configuration on a computer or on a Group Policy Object (GPO).

Parameters

-AsJob

-CimSession<CimSession[]>

Runs the cmdlet in a remote session or on a remote computer. Enter a computer name or a session object, such as the output of a New-CimSession or Get-CimSession cmdlet. The default is the current session on the local computer.

-GPOSession<String>

Specifies the Group Policy session to which to store the configuration information.
You can use this with the NetGPO cmdlets to aggregate multiple operations performed on a GPO.
You cannot use this parameter with the PolicyStore parameter.

-InputObject<CimInstance[]>

Specifies the object which contains ISATAP configuration to set.

-IPInterface<CimInstance>

Specifies the IP interface on which to set the ISATAP configuration.

-PassThru

Returns an object representing the item with which you are working. By default, this cmdlet does not generate any output.

-PolicyStore<String>

Specifies the policy store that contains the configuration to set.
The acceptable values for this parameter are:
-- PersistentStore
-- ActiveStore
-- GPO
To set the configuration of a GPO, specify the GPO name using the following format: Domain\GPOName
You cannot use this parameter with the GPOSession parameter.

-ResolutionIntervalSeconds<UInt32>

Specifies how often in seconds that Windows Server® 2012 attempts to contact the specified ISATAP server.

-ResolutionState<State>

Specifies the state of router name resolution. The state of the router name resolution specifies how often Windows Server 2012 resolves the ISATAP router name.

-Router<String>

Specifies the policy setting that allows you to specify a router name or IPv4 address for an ISATAP router.
If you enable this policy setting, then you can specify a router name or IPv4 address for an ISATAP router. If you enter an IPv4 address of the ISATAP router, then DNS services are not required.

-State<State>

Specifies the policy setting that allows you to configure ISATAP, an address-to-router and host-to-host, host-to-router and router-to-host automatic tunneling technology that provides unicast IPv6 connectivity between IPv6 hosts across an IPv4 intranet.
You can specify one of the following three policy setting states:
-- Default: If the ISATAP router name is resolved successfully, then ISATAP is configured with a link-local address and an address for each prefix received from the ISATAP router through stateless address auto-configuration.
---- If the ISATAP router name is not resolved successfully, then ISATAP connectivity is not available on the host using the corresponding IPv4 address.
-- Enabled:
---- If the ISATAP name is resolved successfully, then ISATAP is configured with a link-local address and an address for each prefix received from the ISATAP router through stateless address auto-configuration.
---- If the ISATAP name is not resolved successfully, then the ISATAP interface is configured with a link-local address.
-- Disabled: No ISATAP interfaces are present on the host.

-ThrottleLimit<Int32>

Specifies the maximum number of concurrent operations that can be established to run the cmdlet. If this parameter is omitted or a value of 0 is entered, then Windows PowerShell® calculates an optimum throttle limit for the cmdlet based on the number of CIM cmdlets that are running on the computer. The throttle limit applies only to the current cmdlet, not to the session or to the computer.

-Confirm

Prompts you for confirmation before running the cmdlet.

-WhatIf

Shows what would happen if the cmdlet runs. The cmdlet is not run.

<CommonParameters>

This cmdlet supports the common parameters: -Verbose, -Debug, -ErrorAction, -ErrorVariable, -OutBuffer, and -OutVariable. For more information, see    about_CommonParameters (https://go.microsoft.com/fwlink/p/?LinkID=113216).

Inputs

The input type is the type of the objects that you can pipe to the cmdlet.

• None

  This cmdlet accepts no input objects.

Outputs

The output type is the type of the objects that the cmdlet emits.

• Microsoft.Management.Infrastructure.CimInstance#root\StandardCimv2\MSFT_NetISATAPConfiguration

  The Microsoft.Management.Infrastructure.CimInstance object is a wrapper class that displays Windows Management Instrumentation (WMI) objects. The path after the pound sign (#) provides the namespace and class name for the underlying WMI object.
  When the Passthru parameter is specified, this cmdlet outputs a modified ISATAP configuration object.

Examples

Example 1: Set ISATAP configuration

This command modifies the router name.

PS C:\> Set-NetIsatapConfiguration -Router superisatap

Example 2: Set a router using an input object

This set of commands uses the Get-NetIPInterface and Get-NetIsatapConfiguration cmdlets to get the ISATAP configuration of the interface at index 14 and stores it in a variable named $config, and then sets the router name to SuperIsatap using this cmdlet.

PS C:\> $config = ( Get-NetIPInterface -InterfaceIndex 14 | Get-NetIPISATAPConfiguration )

PS C:\> $config.Router = "SuperIsatap"

PS C:\> Set-NetIsatapConfiguration -InputObject $config

Related topics

Get-NetIPInterface

Get-NetIsatapConfiguration

Set-NetIsatapConfiguration